Homelite UT10680 User Manual - Page 15

Caution

Get Homelite UT10680 PDF manuals and user guides View all Homelite UT10680 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

OPERATION n Place the chain saw on level ground and ensure that no objects or obstructions are in the immediate vicinity that could come in contact with the bar and chain. ON/STOP SWITCH IN THE RUN POSITION n Hold the front handle firmly with your left hand STOP and put your right foot onto the base of the rear handle. To start a cold engine: n Set the on/stop switch to the RUN ( I ) position. n Make sure the chain brake is in the run position by pulling back on the lever/hand guard. n Fully press and release the primer bulb 7 times. n Pull choke lever all the way out to FULL position. n When the temperature is above 50°F, pull the starter grip and rope until the engine attempts to start, but no more than 3 times. When the temperature is below 50°F, pull the starter grip STOP and rope until the engine attempts to start, but PRIMER BULB no more than 5 times. n Push choke lever to RUN position. n Pull starter grip and rope until engine runs. NOTE: Allow the saw to run in this position 1530 seconds, depending upon the temperature. n Depress the trigger release and squeeze and release the throttle trigger to return the engine to idle. CAUTION: Failure to release partial throttle when chain brake lever is in the brake position will result in serious damage to the unit. Never squeeze and hold the throttle trigger while the chain brake is in the brake position. CHOKE LEVER STOP To start a warm engine: n Set the on/stop switch to the RUN ( I ) position. n Make sure the chain brake is in the run position by pulling back on the lever/hand guard. n Pull choke lever out to FULL CHOKE position then push immediately back to RUN position to set fast idle. FULL CHOKE RUN POSITION Page 15 - English Fig. 7 RUN POSITION Fig. 8 STOP Fig. 9 Fig. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Page 15
— English
STOP
STOP
OPERATION
Place the chain saw on level ground and ensure
that no objects or obstructions are in the imme-
diate vicinity that could come in contact with the
bar and chain.
Hold the front handle firmly with your left hand
and put your right foot onto the base of the rear
handle.
To start a cold engine:
Set the on/stop switch to the
RUN (
I
)
posi-
tion.
Make sure the chain brake is in the run position
by pulling back on the lever/hand guard.
Fully press and release the primer bulb 7
times.
Pull choke lever all the way out to
FULL
posi-
tion.
When the temperature is above 50°F, pull the
starter grip and rope until the engine attempts
to start, but no more than 3 times. When the
temperature is below 50°F, pull the starter grip
and rope until the engine attempts to start, but
no more than 5 times.
Push choke lever to
RUN
position.
Pull starter grip and rope until engine runs.
NOTE:
Allow the saw to run in this position 15-
30 seconds, depending upon the temperature.
Depress the trigger release and squeeze and
release the throttle trigger to return the engine
to idle.
CAUTION:
Failure to release partial throttle when chain
brake lever is in the brake position will result in
serious damage to the unit. Never squeeze and
hold the throttle trigger while the chain brake is
in the brake position.
To start a warm engine:
Set the on/stop switch to the
RUN (
I
)
posi-
tion.
Make sure the chain brake is in the run position
by pulling back on the lever/hand guard.
Pull choke lever out to
FULL CHOKE
position
then push immediately back to
RUN
position to
set fast idle.
ON/STOP
SWITCH IN THE
RUN POSITION
Fig. 7
PRIMER BULB
Fig. 9
Fig. 10
FULL CHOKE
CHOKE LEVER
RUN POSITION
Fig. 8
RUN
POSITION