Homelite UT43160 User Manual - Page 12

Operation

Get Homelite UT43160 PDF manuals and user guides View all Homelite UT43160 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

OPERATION APPLICATIONS You may use this product for the purposes listed below: n Limbing n Pruning LUCBHRAICINANT OIL RESERVOIR CAP ADDING BAR AND CHAIN LUBRICANT See Figure 4 Use HOMELITE Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. NOTE: Pole saw comes from the factory with no bar and chain oil added. Level should also be checked after every 20 minutes of use and refilled as needed. n Remove oil cap. n Carefully pour the bar and chain oil into the tank. n Wipe off excess oil. n Check and fill the oil tank when quick view oil indicator is below the second to last indicator line. n Repeat as needed. NOTE: Do not use dirty, used or otherwise contaminated oils. Damage may occur to the bar or chain. NOTE: It is normal for oil to seep from the saw when not in use. To prevent seepage, empty the oil tank after each use then run for one minute. When storing the unit for a long period of time (three months or longer) be sure the chain is lightly lubricated; this will prevent rust on the chain and bar sprocket. QUICK VIEW OIL INDICATOR LOCK-OUT BUTTON Fig. 4 SWITCH TRIGGER CORD RETAINER Fig. 5 n Plug product into extension cord. NOTE: Failure to remove all excess cord slack from extension cord retainer could result in plug loosening from receptacle. STARTING AND STOPPING See Figure 5. CONNECTING TO POWER SUPPLY See Figure 5. This product is designed with a cord retainer that prevents the extension cord from being pulled loose while using. n Form a loop with the end of the extension cord. n Insert loop portion of extension cord through opening in the bottom of the rear handle and place over cord retainer. n Slowly pull loop against cord retainer until the slack is ­removed. To start the motor: n Connect the pole saw to power supply. n Place your thumb on the lock-out button and pull it completely towards you. n Fully depress the switch trigger. To stop the motor: n Release the switch trigger. Page 12 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Page 12
— English
OPERATION
APPLICATIONS
You may use this product for the purposes listed
below:
Limbing
Pruning
ADDING BAR AND CHAIN LUBRICANT
See Figure 4
Use HOMELITE Bar and Chain Lubricant. It is
designed for chains and chain oilers, and is for-
mulated to perform over a wide temperature range
with no dilution required.
NOTE:
Pole saw comes from the factory with
no bar and chain oil added. Level should also be
checked after every 20 minutes of use and refilled
as needed.
Remove oil cap.
Carefully pour the bar and chain oil into the
tank.
Wipe off excess oil.
Check and fill the oil tank when quick view oil
indicator is below the second to last indicator
line.
Repeat as needed.
NOTE:
Do not use dirty, used or otherwise
contaminated oils. Damage may occur to the
bar or chain.
NOTE:
It is normal for oil to seep from the saw
when not in use. To prevent seepage, empty the
oil tank after each use then run for one minute.
When storing the unit for a long period of time
(three months or longer) be sure the chain is lightly
lubricated; this will prevent rust on the chain and
bar sprocket.
CONNECTING TO POWER SUPPLY
See Figure 5.
This product is designed with a cord retainer that
prevents the extension cord from being pulled
loose while using.
Form a loop with the end of the extension
cord.
Insert loop portion of extension cord through
opening in the bottom of the rear handle and
place over cord retainer.
Slowly pull loop against cord retainer until the
slack is removed.
Fig. 5
LOCK-OUT BUTTON
SWITCH TRIGGER
CORD RETAINER
Plug product into extension cord.
NOTE:
Failure to remove all excess cord slack
from extension cord retainer could result in plug
loosening from receptacle.
STARTING AND STOPPING
See Figure 5.
To start the motor:
Connect the pole saw to power supply.
Place your thumb on the lock-out button and
pull it completely towards you.
Fully depress the switch trigger.
To stop the motor:
Release the switch trigger.
Fig. 4
CHAIN
LUBRICANT
OIL
RESERVOIR
CAP
QUICK VIEW
OIL INDICATOR