Honeywell 6160CR-2 Setup Guide - Page 2

ÊK3590-2CF2Š - red fire keypad

Get Honeywell 6160CR-2 PDF manuals and user guides View all Honeywell 6160CR-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

BLACK RED Y+ G Set the desired address: Enter the desired address. For example, for address 12, enter 1, then 2. Display shows (12). 2. Exit the address mode: Press the "star" key (✻) to save the displayed address and exit the address mode. The current address may be viewed at any time by pressing and holding [1] and [3] keys together. + + + + + + + + 6160CR-004-V1 Figure 2 - 6160CR-2 Wiring Details SETTING THE KEYPAD ADDRESS The keypad address must be set according to the control panel being used (refer to the individual control panel's instructions for details). Available addresses are from 00 through 30. The keypad is shipped with a default address of 31 (non-addressable mode). To change the address, do the following: 1. Enter keypad address mode: Power up the keypad. Within 60 seconds of power-up, press and hold down the [1] and [3] keys together for 3seconds. The current address will be displayed and the cursor will be under the "tens" digit (31). Notes: • If the system has been powered up for more than 60 seconds, you must power the keypad down, and then power it up again in order to change the keypad's address. • The keypad will not enter the address mode if the system is in the program mode. • If 10 seconds have passed with no key entry, the keypad automatically exits the address mode. KEYPAD LABELS Function key labels: A set of adhesive-backed labels with some typical function symbols (e.g., police, emergency, etc.) is provided. These labels come in four colors (red, blue, green, and white) and may be placed on the appropriate function keys (A, B, or C) for ease of identifying the individual key's function (as determined by the control panel's capability and programming). OPERATING THE KEYPAD For operating instructions, see the User Guide for the control panel with which this keypad is used. SPECIFICATIONS Physical: 5.25" H x 7.437" W x 1.312" D Display: Alphanumeric, 32-character (2 lines x 16 characters), LCD back-lit Sounder: Electrical: High-quality speaker Voltage: +12VDC (from power-limited source) Current: 45mA standby; 160mA in alarm (sounder, back light and LEDs on) NFPA-72 Compliant FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM, REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED. ÊK3590-2CF2Š K3590-2CF 9/08 Rev. B 2 Corporate Center Drive, Suite 100 P.O. Box 9040 Melville, NY 11747 Copyright © 2007 Honeywell International Inc. www.security.honeywell.com

  • 1
  • 2
6160CR-004-V1
+
+
+
+
RED
BLACK
+
+
+
+
Y
G
+
Figure 2 – 6160CR-2 Wiring Details
SETTING THE KEYPAD ADDRESS
The keypad address must be set according to the control
panel being used (refer to the individual control panel’s
instructions for details). Available addresses are from 00
through 30. The keypad is shipped with a default address
of 31 (non-addressable mode). To change the address, do
the following:
1.
Enter keypad address mode:
Power up the keypad. Within 60 seconds of power-up,
press and hold down the [1] and [3] keys together for 3-
seconds. The current address will be displayed and the
cursor will be under the “tens” digit (
3
1
).
Notes:
•
If the system has been powered up for more than 60
seconds, you must power the keypad down, and then
power it up again in order to change the keypad’s
address.
•
The keypad will not enter the address mode if the system
is in the program mode.
•
If 10 seconds have passed with no key entry, the keypad
automatically exits the address mode.
Set the desired address:
Enter the desired address. For example, for address 12,
enter 1, then 2. Display shows (12).
2.
Exit the address mode:
Press the “star” key
(
✻
)
to save the displayed address
and exit the address mode.
The current address may be
viewed at any time by pressing and holding [1] and [3]
keys together.
KEYPAD LABELS
Function key labels:
A set of adhesive-backed labels
with
some
typical
function
symbols
(e.g.,
police,
emergency, etc.) is provided. These labels come in four
colors (red, blue, green, and white) and may be placed on
the appropriate function keys (A, B, or C) for ease of
identifying the individual key’s function (as determined by
the control panel’s capability and programming).
OPERATING THE KEYPAD
For operating instructions, see the User Guide for the
control panel with which this keypad is used.
SPECIFICATIONS
Physical:
5.25” H x 7.437” W x 1.312” D
Display:
Alphanumeric, 32-character (2 lines x 16
characters), LCD back-lit
Sounder:
High-quality speaker
Electrical:
Voltage: +12VDC (from power-limited
source)
Current: 45mA standby;
160mA in alarm (sounder, back
light and LEDs on)
NFPA-72
Compliant
FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM, REFER TO THE INSTALLATION AND
SETUP GUIDE FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED.
ÊK3590-2CF2Š
K3590-2CF
9/08
Rev. B
2 Corporate Center Drive, Suite 100
P.O. Box 9040
Melville, NY 11747
Copyright
© 2007 Honeywell International Inc.
www.security.honeywell.com