Honeywell HFD-135 User Guide - Page 5

Cleaning The Pre-filter, Removing / Cleaning The Ifd, Filter, Replacing The Ultraviolet Uv Lamps - ifd air purifier w ultraviolet system

Page 5 highlights

HFD-135 OM English.qxd 10/14/05 5:35 PM Page 5 REMOVING / CLEANING THE IFD™ FILTER (CONTINUED) CAUTION: • Never place a wet IFD™ filter in your air purifier. • The IFD™ Filter is NOT dishwasher safe. Do not place the IFD™ filter in a dishwasher or subject it to other extreme hot water conditions. • Do not use any solvents, strong cleaning agents or flammable liquids to clean the IFD™ filter. Resetting the Filter Clean Indicator After cleaning the IFD™ filter, you need to reset the filter monitor. • Once the IFD™ filter has been checked and cleaned, the filter monitor will need to be reset. • With the air purifier unit powered on, press and hold the filter reset button for approximately 10 seconds or until the LCD display is clear. CLEANING THE PRE-FILTER The particle pre-filter helps pick-up large airborne particles that enter the filter. The pre-filter can be removed and rinsed by hand under warm water. Let the pre-filter dry completely before inserting it back into the unit. REPLACING THE ULTRAVIOLET (UV) LAMPS The UV Reset LED light will illuminate when it is time to replace the dual UV bulbs. "Replace UV Bulb" will also appear in the control panel. Fig. 12 Fig. 13 Fig. 14 • Be sure to turn off and unplug your air purifier. • Remove the UV cover (Fig. 12). • Turn the UV bulb tab towards the unlock symbol ( ) (Fig. 13). Fig. 15 • Gently grasp the top of the tab and pull the bulb cartridge straight out of the UV socket (Fig. 14). Do not touch the bulb directly with your hands. • Do the same for the other bulb and pull the bulb cartridge out of the UV socket. • Replace the left and right UV bulb sockets with new UV lamps (part number 135UV). • Discard old UV bulb cartridge(s) only at household hazardous waste collection sites. • Place UV cover back in to its place until it clicks in position. • Plug the air purifier back into an electrical socket and turn the air purifier on. • Press and hold the UV Reset button for 10 seconds to clear the red LED light and "Replace UV Bulb" message (Fig. 15). NOTE: Bulb and bulb housing are not intended for use with any other product or purpose. NOTE: This unit is equipped with a safety interlock. The unit will not operate while the UV cover is removed. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

CAUTION:
Never place a wet IFD
filter in your air purifier.
The IFD
Filter is NOT dishwasher safe. Do not place the IFD
filter in a dishwasher or subject it to
other extreme hot water conditions.
Do not use any solvents, strong cleaning agents or flammable liquids to clean the IFD
filter.
Resetting the Filter Clean Indicator
After cleaning the IFD
filter, you need to reset the filter monitor.
• Once the IFD
filter has been checked and cleaned, the filter monitor will need to be reset.
• With the air purifier unit powered on, press and hold the filter reset button for approximately 10
seconds or until the LCD display is clear.
CLEANING THE PRE-FILTER
The particle pre-filter helps pick-up large airborne particles that enter the filter. The pre-filter can be
removed and rinsed by hand under warm water. Let the pre-filter dry
completely
before inserting it back
into the unit.
5
REMOVING / CLEANING THE IFD
FILTER (
CONTINUED
)
REPLACING THE ULTRAVIOLET (UV) LAMPS
The UV Reset LED light will illuminate
when it is time to replace the dual UV
bulbs.
“Replace UV Bulb” will also
appear in the control panel.
Be sure to turn off and unplug your
air purifier.
Remove the UV cover (Fig. 12).
Turn the UV bulb tab towards the unlock symbol (
)
(Fig. 13).
Gently grasp the top of the tab and pull the bulb cartridge
straight out of the UV socket (Fig. 14). Do not touch the
bulb directly with your hands.
Do the same for the other bulb and pull the bulb cartridge
out of the UV socket.
Replace the left and right UV bulb sockets with new UV
lamps (part number
135UV
).
Discard old UV bulb cartridge(s) only at household hazardous waste collection sites.
Place UV cover back in to its place until it clicks in position.
Plug the air purifier back into an electrical socket and turn the air purifier on.
Press and hold the UV Reset button for 10 seconds to clear the red LED light and “Replace UV Bulb”
message (Fig. 15).
NOTE:
Bulb and bulb housing are not intended for use with any other product or purpose.
NOTE:
This unit is equipped with a safety interlock. The unit will not operate while the UV cover is
removed.
Fig. 15
Fig. 14
Fig. 12
Fig. 13
HFD-135 OM English.qxd
10/14/05
5:35 PM
Page 5