Honeywell HW4000L Owners Manual - Page 14

Step 2: Install Wheel Axle and Wheels, To install wheel assembly, you will need

Get Honeywell HW4000L - Portable Generator PDF manuals and user guides
UPC - 894190002094
View all Honeywell HW4000L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Assembly Step 2: Install Wheel Axle and Wheels To install wheel assembly, you will need: ‰ Wheel axle (1) ‰ M8 x 16 mm long full-thread hex flange bolts (4) ‰ M8 serrated flange nuts (4) ‰ Axle bracket* (1) ‰ Wheels (2) ‰ M16 x 30 mm OD x 2 mm washers (2) ‰ Cotter pins (2) ‰ 13 mm open end wrench† ‰ Socket wrench with 13 mm socket† ‰ Needle-nose pliers† * Two brackets are needed to install wheel axle. One bracket comes already attached to wheel axle; other bracket is included in wheel kit box. † Not included. 1. Install wheel axle brackets to frame using 16 mm long full-thread hex flange bolts and serrated flange nuts. 1A. Install pre-attached bracket to frame first. 1B. Install other bracket (included in hardware bag) to frame. 3. Slide a washer onto axle. 4. Slide cotter pin into pre-drilled hole until fully seated. 5. Using needle-nose pliers, bend each end of cotter pin in opposing directions to secure wheel to axle. FIGURE 10: Cotter Pin Installation 6. Return generator to upright position (so that wheels and leg supports are touching the ground). FIGURE 8: Wheel Axle Attached to Generator On each end of axle: 2. Slide and push wheel onto axle until it fits snug against washer. FIGURE 9: Slide Wheel onto Wheel Axle NOTE: Axle brackets are offset (one side longer than the other), place with the short side up during installation. 8 www.honeywellgenerators.com HW4000/HW4000L Portable Electrical Generator Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Assembly
8
www.honeywellgenerators.com
HW4000/HW4000L Portable Electrical Generator Owner’s Manual
Step 2: Install Wheel Axle and Wheels
1.
Install wheel axle brackets to frame using 16 mm long
full-thread hex flange bolts and serrated flange nuts.
1A.
Install pre-attached bracket to frame first.
1B.
Install other bracket (included in hardware bag) to
frame.
On each end of axle:
2.
Slide and push wheel onto axle until it fits snug
against washer.
NOTE:
Axle brackets are offset (one side longer than the other),
place with the short side up during installation.
3.
Slide a washer onto axle.
4.
Slide cotter pin into pre-drilled hole until fully seated.
5.
Using needle-nose pliers, bend each end of cotter pin
in opposing directions to secure wheel to axle.
6.
Return generator to upright position (so that wheels
and leg supports are touching the ground).
To install wheel assembly, you will need:
±
Wheel axle (1)
±
M8 x 16 mm long full-thread hex flange bolts (4)
±
M8 serrated flange nuts (4)
±
Axle bracket
*
(1)
*
Two brackets are needed to install wheel axle. One bracket
comes already attached to wheel axle; other bracket is included
in wheel kit box.
±
Wheels (2)
±
M16 x 30 mm OD x 2 mm washers (2)
±
Cotter pins (2)
±
13 mm open end wrench
†
±
Socket wrench with 13 mm socket
†
†
Not included.
±
Needle-nose pliers
†
FIGURE 8:
Wheel Axle Attached to Generator
FIGURE 9:
Slide Wheel onto Wheel Axle
FIGURE 10:
Cotter Pin Installation