Hoover BH14000VCK Product Manual English - Page 2
Battery Disposal, Warning
View all Hoover BH14000VCK manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
• DO NOT USE THIS EXTRACTOR ON HARD FLOORS UNLESS YOU HAVE THE PROPER HARD FLOOR ATTACHMENT. USING THIS PRODUCT ON HARD FLOORS MAY SCRATCH OR DAMAGE YOUR FLOOR. • Water will drip from the tool after use and may puddle. To avoid damage to wood and laminate flooring and to avoid potential slip hazard, after use (a) do not leave the product on wood and laminate surfaces and remove to a hard surface and (b) place unit on absorbent material (such as a towel) to soak up drips. BATTERY DISPOSAL WARNING - RISK OF EXPLOSION OR EXPOSURE TO TOXIC MATERIAL LITHIUM-ION BATTERIES The battery must be collected, recycled or disposed of in an environmentally sound manner. The EPA certified RBRC Battery Recycling Seal on the lithium-ion [Li-ion] battery indicated Techtronic Industries, is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Li-ion batteries into the trash or the municipal waste stream, which may be illegal in your area. Please visit www.rbrc.org/ call2recycle/ for information on Li-ion battery recycling and disposal bans/restrictions in your area. HOOVER's involvement in this program is part of our commitment to preserving our environment and conserving our natural resources. GETTING STARTED The charger included with your Clean Slate may differ from what is shown in this user manual. Please reference the Accessories section of this manual or contact us at Hoover.com for more information of your specific charger. CAUTION: Not to be used for grooming a pet. 1 Place battery into unit, remove Solution Tank from the side of the unit, then remove the cap. 2 Follow the formula ratio chart and use the included measuring cup to add cleaning formula in the Solution Tank. CLEANING FLUID: SEE THE HOOVER SOLUTION GUIDE insert or visit Hoover. com/cleaningsolutions. 3 Replace and tighten cap. Slide the Solution Tank back into the unit to secure the tank. 4 Unwrap hose from unit. Select preferred tool and make sure it is attached securely. OPERATION BEFORE YOU BEGIN CLEANING Use your Hoover upholstery and spot cleaner only if upholstery fabric is marked with a "W" (for "wet" clean) or "S/W" (for "solvent/dry" or "wet" clean). Don't clean fabric marked "S" ("solvent/ dry" clean only). Test for colorfastness in a small, hidden area. Gently rub surface with a dampened white cloth. Wait ten minutes and check for color removal or bleed with a white paper towel. NOTE: To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray. NOTE: To avoid damage to wood floors underneath area rugs or carpet, place waterproof material (e.g. plastic) underneath them before cleaning. CAUTION: DO NOT USE THIS EXTRACTOR ON HARD FLOORS. USING THIS PRODUCT ON HARD FLOORS MAY SCRATCH OR DAMAGE YOUR FLOOR. CAUTION: Do not clean over floor electrical outlets. Water will drip from the tool after use and may puddle. To avoid damage to wood and laminate flooring and to avoid potential slip hazard, after use (a)do not leave the product on wood and laminate surfaces and move to a hard surface and (b) place unit on an absorbent material (such as a towel) to soak up drips. 1 Press Red Power button on the handle to turn ON. 2 When cleaning tough stains, use boost mode for more power. Press the (+) sign located under the power button. To turn off boost mode, press the (+) sign again. Using boost mode reduces run time to up to 15 min. 3 First, remove any large debris before using the machine. Use preferred tool to suction up any excess liquid from the stain. Hold tool about 5 inches over the spot or stain. Spray a generous amount of cleaning solution over the soiled area by pressing the trigger behind the tool and scrub the stain in a backand-forth motion. 4 To lift the stain, suction up the dirt and cleaning solution by applying downward pressure on the front of the cleaning tool and pulling towards you. Repeat as needed. IMPORTANT: Empty the Recovery Tank when it reaches the MAX fill line. There will be an audible change, lights will flash and the unit will turn off. Ensure the tank is secured before cleaning. MAINTENANCE WARNING: To reduce the risk from moving parts, remove the battery before servicing. WARNING: To reduce risk of fire and electric shock due to internal component damage, use only HOOVER® cleaning products intended for use with the appliance as noted. HOW TO CLEAN RECOVERY TANK Leave the battery in machine. Press TANK RELEASE button. Then lift lid off for emptying and rinsing. Clean water will help remove dirt & debris from the tank. Let air dry before reinstalling. HOW TO CLEAN TOOLS 1 Remove the tool from the hose. Rinse hand tool under faucet. Remove nozzle cover by unlatching from the top. 2 Pull the release tab to remove the insert and rinse under faucet. HOW TO CLEAN HOSE 1 Remove the solution tank and fill with warm water (max 140˚F (60˚C)) to the small area fill line.