Hoover Cleanslate Plus Carpet & Upholstery with Pet Kit Product Manual English - Page 2

GETTING STARTED OPERATION MAINTENANCE HOW TO CLEAN TOOLS HOW TO CLEAN HOSE (CONT'D) 1 Remove Solution Tank from the side of the unit, then remove the cap. CAUTION: WARNING: Do not clean over To reduce the risk floor electrical outlets. Water will of personal injury - Unplug before drip from the tool after use and may cleaning or servicing. puddle. To avoid damage to wood and laminate flooring and to avoid potential slip hazard, after use (a) do not leave the product on wood and laminate surfaces and move to a hard surface and (b) place unit on an absorbent material (such as a towel) to soak up drips. WARNING: To reduce risk of fire and electric shock due to internal component damage, use only HOOVER® cleaning products intended for use with the appliance as noted. This product contains no serviceable parts. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1.800.944.9200 prior to continuing use. 1 3 Remove the tool from the hose. Rinse Ensure both the solution and recovery hand tool under faucet. Remove the tanks are secured on unit. Turn unit on nozzle cover by unlatching the clear tab. and hold the trigger for 30 seconds. The clean water will rush through the hose, effectively cleaning and removing odor causing bacteria left in the hose. Repeat as needed. Let unit run for 5-10 seconds before turning off. 2 Follow the formula ratio chart to add cleaning formula in the Solution Tank. 3 Replace and tighten cap. Slide the tank back into the unit. The tank is secured when you feel a click. 1 Press Red Power button on top of unit to turn ON. 2 Hold tool about 5 inches over the spot or stain. Spray a generous amount of cleaning solution over the soiled area by pressing the trigger behind the tool and scrub the stain in a back and forth motion. HOW TO CLEAN THE RECOVERY TANK 2 Remove Insert and rinse under faucet. 4 Repeat process as needed and turn off the unit when hose is fully clean. Empty the recovery tank. HOW TO CLEAN HOSE 1 Remove the solution tank and fill with 1 warm water (max 140˚F (60˚C)) to the small area fill line. Press TANK RELEASE button then lift lid off for emptying and rinsing. Clean water will help remove dirt & debris from the tank. Let air dry before reinstalling. 2 Remove any cleaning tool or attachment from the hose, and attach the Hose Rinse Tool to the hose. THERMAL PROTECTION A thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates the cleaner will stop running. If this happens proceed as follows: 1. Turn cleaner OFF and unplug it from the electrical outlet. 2. Empty Recovery Tank. 3. Inspect for any obstructions. Clear obstructions if present. 4. When cleaner is unplugged and motor cools for 30 minutes, the thermal protector will deactivate and cleaning may continue. If the thermal protector continues to activate after following the above steps, your cleaner needs servicing. FORMULA RATIO CHART IF USING HOOVER CONCENTRATE SMALL AREA (20 OZ) LARGE AREA (40 OZ) Water Fill water Small Area Line (20 oz) Fill water Large Area Line (39 oz) HOOVER 2X Concentrated Formula 0.5 oz 1 oz Clean Complements Enhancer Up to 1 oz Up to 1 oz 3 IF USING HOOVER READY-TO-USE PREMIX 4 To lift the stain, suction up the dirt and cleaning solution by applying downward Unwrap hose from unit. Select preferred pressure on the front of the cleaning tool and make sure it is attached securely. tool and pulling towards you. Repeat as needed. NOTE: Read the directions on the HOOVER® Carpet Cleaning fluid prior to use. IMPORTANT: Empty the Recovery Tank when it reaches the MAX fill line or you CLEANING FLUID: SEE THE HOOVER hear an audible change. Ensure the tank SOLUTION GUIDE insert or visit Hoover. is secured before cleaning. Ensure the com/cleaning-solutions. tank is secured before cleaning. Premixed Formula Clean Complements Enhancer Fill premix Small Area Line Up to 1 oz Fill premix Large Area Line Up to 1 oz WARNING: TROUBLESHOOTING To reduce the risk of personal injury - Unplug before cleaning or servicing. REPLACEMENT PARTS AND ACCESSORIES SUCH AS SOLUTIONS AVAILABLE AT HOOVER.COM. IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE. ALWAYS IDENTIFY YOUR CLEANER BY THE COMPLETE MODEL NUMBER. (THE MODEL NUMBER APPEARS ON THE BOTTOM OF THE CLEANER.) CAUTION: Not to be used for grooming a pet. For best results, pretreat stains with a HOOVER® spot treatment (see HOOVER® Cleaning Solution Guide) to help loosen and PROBLEM Cleaner won't run CAUTION: DO NOT USE THIS remove even the most stubborn stains. Distribute a generous amount of pretreat spray EXTRACTOR ON HARD FLOORS. USING on spot, stain, or high traffic area. THIS PRODUCT ON HARD FLOORS MAY Always follow specific directions found on Cleaner won't pick-up or low suction SCRATCH OR DAMAGE YOUR FLOOR. solution label. Before You Begin Cleaning Wait 5-10 minutes before using machine. Use your Hoover upholstery and spot cleaner only if upholstery fabric is marked with a "W" (for "wet" clean) or "S/W" (for "solvent/dry" or "wet" clean). Don't clean fabric marked "S" ("solvent/ dry" clean only). Test for colorfastness in a small, hidden area. Gently rub surface with a dampened white STORAGE: Wrap cord around the cord Water escaping from Cleaner hooks for convenient storage. Attach the plug end to the cord. For fast cord release, simply turn the cord wraps 180 degrees to the right or left. Cleaner won't dispense cloth. Wait ten minutes and check for color removal or bleed with a white paper towel. NOTE: To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray. NOTE: To avoid damage to wood floors underneath area rugs or carpet, place waterproof material (e.g. plastic) underneath them before cleaning. LUBRICATION: The motor is equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor bearings. Tools and formula may vary by model. Hose nozzle will not spray after filling the Clean Water Tank or Solution Tank Container. Motor noise becomes high-pitched POSSIBLE CAUSE 1. Power cord not firmly plugged into outlet. 2. Blown fuse or tripped breaker. 3. Needs service. 1. Recovery Tank is not installed correctly. 2. Recovery Tank is full. 3. Recovery Tank is clogged. 4. Air path is clogged. 5. Recovery Tank debris filter is clogged. 1. Recovery Tank is full. 2. Recovery Tank is not installed correctly. 3. Solution Tank not installed properly. POSSIBLE SOLUTION 1. Plug unit in firmly. 2. Check fuse or breaker in home. Replace fuse/reset breaker in home. 3. Visit our website at www.hoover.com or call 1-800-944-9200. 1. Check placement of Recovery Tank in base of cleaner. 2. Empty Recovery Tank. 3. Clean Recovery Tank. 4. Remove Hose and Flush out with Clean Water. 5. Remove debris filter and rinse thoroughly, then replace. 1. Empty Recovery Tank. 2. Check placement of Recovery Tank in base of cleaner. 3. Review "Getting Started" for Solution Tank Installation. 1. Solution Tank is empty. 2. Solution Tank not installed properly. 3. Needs service. 1. Fill Solution Tank. 2. Review "Getting Started" Solution Tank Installation. 3. Visit our website at www.hoover.com or call 1-800-944-9200. 1. Air is trapped in the pump and hose. 1. T urn on the cleaner. If hose does not spray, prime the pump by lowering the hose down to the floor and hold the trigger for up to 1 minute. 1. Recovery Tank is full. 1. Empty Recovery Tank. 2. Recovery Tank is clogged. 2. Clean the Recovery Tank. 3. Air path is clogged. 3. Unclog air path. 4. The float in the Recovery Tank has been activated. 4. Review Cleaning the Recovery Tank.