Hoover DOLARGAPP4059324 User Guide - Page 10

replacement, electrical, Brush

Get Hoover DOLARGAPP4059324 - WindTunnel Anniversary PDF manuals and user guides
UPC - 961613066589
View all Hoover DOLARGAPP4059324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Installing lens bulb and replacing Pull old bulb straight out of socket. Push new bulb straight into socket until locked in place. Excessive force is not required. Reposition screws. lens and secure with the two Belt replacement The belts are located under the bottom plate of the cleaner checked from time and should be to time to be sure they are in good condition, The flat (wide) belt is described below; the other is described under "Brush roll replacement". When to replace Disconnect cleaner from electrical outlet. Warning - Brush roll can start suddenly. Unplug cleaner when it is turned over. To check the flat belt, remove bottom plate as shown in Fig. 3-9. Replace belt if it is stretched, cut or broken. What to buy To assure effective operation, use only genuine HOOVER belts with your clean- er. When purchasing a new belt, ask for: Flat belt - HOOVER part No. 38528035. Replacing flat belt Removing bottom plate Disconnect cleaner from electrical outlet. Warning - Brush roll can start suddenly. Unplug cleaner when it is turned over. Place handle in low position and turn cleaner over so bottom side is up. Remove 4 the screws as shown with a Phillips screw driver. Lift off bottom plate (A) Removing belt Flat belt (B) operates the self-propel ture and indirectly drives the brush fearoll. Remove (C) and used belt discard. (B) from large pulley \ Positioning With new lettering belt over back of belt on outside of belt, motor shaft (U). slide Brush roll replacement Positioning Front or belt Place other end (C) while rolling shown, of belt over large pulley the pulley in direction Replacing bottom plate Reposition bottom plate 4 and Phillips Plead screws. Tighten screws securely. 10 When to replace Disconnect cleaner from electrical outlet. Warning - Brush roll can start suddenly. Unplug cleaner when it is turned over. When brush roll brushes are worn, it should be replaced. To check condition of brushes, move the edge of a card while turning brush across bottom roll. To maintain plate cleaning effectiveness, replace brush roll if brushes do not touch card. What to buy When purchasing a new brush roll, ask for HOOVER part No. 48414069.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Installing
bulb
and
replacing
lens
Pull
old
bulb
straight
out
of
socket.
Push
new
bulb
straight
into
socket
until
locked
in
place.
Excessive
force
is
not
required.
Reposition
lens
and
secure
with
the
two
screws.
Belt
replacement
The
belts
are
located
under
the
bottom
plate
of
the
cleaner
and
should
be
checked
from
time
to
time
to
be
sure
they
are
in
good
condition,
The
flat
(wide)
belt
is described
below;
the
other
is
described
under
"Brush
roll
replacement".
When
to
replace
Disconnect
cleaner from
electrical
outlet.
Warning
- Brush roll can start
suddenly.
Unplug cleaner when it
is turned over.
To
check
the
flat
belt,
remove
bottom
plate
as
shown
in
Fig.
3-9.
Replace
belt
if
it
is
stretched,
cut
or
broken.
What
to
buy
To
assure
effective
operation,
use
only
genuine
HOOVER
belts
with
your
clean-
er.
When
purchasing
a
new
belt,
ask
for:
Flat belt
-
HOOVER part
No.
38528035.
Replacing
flat
belt
Removing
bottom
plate
Disconnect
cleaner
from
electrical
outlet.
Warning
- Brush roll can start
suddenly.
Unplug cleaner when it
is turned over.
Place
handle
in
low
position
and
turn
cleaner
over
so
bottom
side
is
up.
Remove
the
4
screws
as
shown
with
a
Phillips
screw
driver.
Lift
off
bottom
plate
(A)
Removing
belt
Flat
belt
(B)
operates
the
self-propel
fea-
ture
and
indirectly
drives
the
brush
roll.
Remove
used
belt
(B)
from
large
pulley
(C)
and
discard.
\
Positioning
back
of
belt
With
lettering
on
outside
of
belt,
slide
new
belt
over
motor
shaft
(U).
Positioning
Front
or
belt
Place
other
end
of
belt
over
large
pulley
(C)
while
rolling
the
pulley
in
direction
shown,
Brush
roll
replacement
Replacing
bottom
plate
Reposition
bottom
plate
and
4
Phillips
Plead
screws.
Tighten
screws
securely.
10
When
to
replace
Disconnect
cleaner
from
electrical
outlet.
Warning
- Brush roll can start
suddenly.
Unplug
cleaner when it
is turned over.
When
brush
roll
brushes
are
worn,
it
should
be
replaced.
To
check
condition
of
brushes,
move
the
edge
of
a
card
across
bottom
plate
while
turning
brush
roll.
To
maintain
cleaning
effectiveness,
replace
brush
roll
if
brushes
do
not
touch
card.
What
to
buy
When
purchasing
a
new
brush
roll,
ask
for HOOVER
part No. 48414069.