Hoover ONEPWR HEPA Cordless Upright Vacuum Product Manual - Page 2

CHARGING THE BATTERY GETTING STARTED HOW TO USE (CONT'D) NOTES: Batteries are shipped in a low charge condition to prevent possible (A) problems. You should charge them before first use. If the light on the charger flashes (B) red, there is an error with the battery or the charger. Try again or call customer service for support at 1-800-406-2005. CHARGING AMBIENT TEMPERATURE RANGE: 5 °C - 40 °C (41 °F - 104 °F). 2 Make sure the filtration bag (A) is attached properly to the bag dock (B). Instructions can be found on the bag and in the maintenance section of this manual. 1 To charge, align the battery to the charger and (A) slide into place. 2 When your battery is charging the lights on the charger will blink. Once charge is complete, lights on the battery will turn off. 3 Step on power head (A) to lower the handle. NOTE: The auto lock feature will disengage motor when vacuum is upright. MAINTENANCE HOW TO REPLACE THE FILTER BAG (CONT'D) REMOVING THE BRUSH ROLL AND BELT CLEARING CLOGS WARNING: WARNING: Risk of personal injury To reduce the risk of - Brush roll may suddenly restart. Turn injury from moving parts - remove battery power switch off and remove battery before before cleaning or servicing. cleaning or servicing. (A) 3 1 Slide a new filtration bag collar firmly into the bag dock ensuring all hooks on dock door are inserted on the cardboard collar. Lay the unit flat to access the power head nozzle. Remove the 7 screws to take off the baseplate from the power head. FILTER BAG MODEL #AH15600 1 An overloaded filtration bag may cause dirt and debris to back up into the air flow system. Open the bag dock and check for visible clogs at the bag port. Change filtration bag if contents have reached the MAXIMUM FILL LINE. 4 2 Remove the brushroll belt and brushroll from Rotate bag dock up and press firmly on the the holding channels inside of the power filtration bag at indicated points until it snaps head nozzle. into place. NORMAL 2 Also, check for blockages in the power head nozzle. QUICK ACCESS BRUSH ROLL CLEANING 3 Press the latches and pull to remove. 4 Push power switch to change between Hard Floor, Carpet and Power OFF modes. MAINTENANCE WARNING: 3 Risk of personal injury - Brush roll may suddenly restart. Turn Rotate both plastic black endcaps at the power switch off and remove battery before ends of the brushroll to show a single notch cleaning or servicing. "NORMAL" position. Insert back into the holding channels of the power head nozzle. NOTE: Ensure both end cap settings are the same facing up when replacing the brush roll. 3 If blockage is not in the power head nozzle, remove the lower tube. Detach rubber straps at bottom of bag and remove screws to tilt battery dock forward. HOW TO INSERT THE BATTERY Fully assemble product prior to use. 1 To insert the battery, align the grooves and slide battery until it clicks into place. To remove, press the latches and slide the battery out. GETTING STARTED HOW TO USE Fully assemble product prior to use. NOTE: Do not operate without a bag. (B) (A) (C) 1 Insert Upper Tube Connector (A) into top of Debris Transfer Tube (C). Twist Upper Tube Connector until it clicks to secure Upper Tube (B). HOW TO REPLACE THE FILTER BAG FILTER BAG MODEL #AH15600 WARNING: To reduce the risk of personal injury, remove battery before cleaning or servicing. Do not use vacuum bag without filtration bag in place. 1 Remove the two black screws, then remove bottom plate. WARNING:Very fine materials, such as face powder or cornstarch may seal the filtration bag and cause it to burst even though it is only partially full. Change the bag often when cleaning this type of material. 2 Find available replacement parts and accessories at Hoover.com. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1.800.406.9005 prior to continuing use. Lift up metal guards to access the brushroll channel. 3 Clear brushroll of debris and obstructions by using scissors to cut across the channel. 1 Unzip the Filtration Bag Case and Pull the cardboard collar downward to release the bag dock from the port. 4 Reassemble the brushroll belt. 5 Manually spin the brushroll to see that it turns freely. 4 Twist lower tube connector counterclockwise and slide up. Pull the lower tube out of the fan housing. Once removed, check for blockage. 6 Replace the 7 screws to secure the baseplate to the power head nozzle. 5 If the lower tube is not blocked, look into the fan housing for blockage. Be sure to reassemble lower tube and tighten the lower MOTOR PROTECTIONS: If the vacuum becomes tube connector before continuing use. overloaded (which could occur when a large obstruction is sucked up or when vacuuming extremely thick carpet), the electronics are designed to shut down the vacuum. If this happens, the vacuum will automatically shut off. To reset the vacuum, turn the unit to "O" or off, then turn on to continue use. If it shuts down again there may be a large obstruction in the vacuum. See Clearing Clogs for the steps on clearing a clog from the air path. THE BELT: This vacuum is equipped with the fiber reinforced stretch belt, which is designed for long life and doesn't need changing. 2 Gently pull the cardboard collar on the filtration bag up to engage the self sealing lock and remove from the bag dock. Discard. 4 Put metal guards back into place and secure wiper back into place with the two black screws. LUBRICATION: The motor and brush roll are equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brush roll. TROUBLESHOOTING FIND AVAILABLE REPLACEMENT PARTS AND ACCESSORIES AT HOOVER.COM. IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-406-2005 PRIOR TO CONTINUING USE. ACCESSORIES GENUINE PARTS AND ACCESSORIES: We recommend using only with genuine HOOVER® replacement bags (for Hoover bagged uprights), parts, and accessories. Damage caused by use with other than genuine HOOVER® bags, parts, and accessories is not covered by and may void your warranty.