Hunter 35216 Owner's Manual - Page 4

Using Your Humidifier

Get Hunter 35216 PDF manuals and user guides View all Hunter 35216 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Using Your Humidifier Initial Setup and Operation 1. Remove the plastic bag covering from the warm mist humidifier. 2. Unravel and straighten the cord before use. 3. Remove the steam unit from the tank. Hold the steam unit securely and press the release button just above the power cord on the back of the steam unit and pull straight up and off. Figure 1. 4. Fill the tank with clean, cool tap water until the water level is is about an inch from the top of the tank. DO NOT OVERFILL. 5. Replace the steam unit in the tank and gently press down until the tabs on the tank snap into place on the steam unit. Figure 2. 6. When using warm mist medications, fill the medicine cup on the steam unit as directed by the medicine package. NOTE: DO NOT add medication of any type into the water in the tank. 7. Plug the power cord into 110-120 Volts AC outlet protected up to 15 Amps. The warm mist will produce a gentle flow of steam within a few minutes. CAUTION: DO NOT use the warm mist with extension cords. NOTE: Protect your floor and furniture by placing the warm mist unit on a nonmetallic, waterproof, heat-resistant surface. 8. If steaming does not start within ten minutes, unplug the steam unit and allow to cool. 9. Remove the steam unit from the tank and add 2 to 3 pinches of ordinary table salt to the water and mix thoroughly. 10. Reassemble the unit. 11. If steaming still does not start after another 10 minutes, add another pinch or two of salt and mix thoroughly. Do not exceed 1/8 teaspon of salt, about 4-5 pinches, as excessive boiling or a blown fuse could occur. Note: Remember the amount of salt you added to start the unit steaming. You will need to add the same amount each time the unit is refilled. Salt has no effect on the purity of the steam or medication. 12. The warm mist will automatically stop producing steam when the water has reached the minimum water level. The refill light will come on to indicate the unit is out of water. Turn the unit off and refill according to the directions above. Caution: ALWAYS unplug the steam unit and allow to cool before removing the tank. Never remove the steam unit before it has cooled as you could be burned or shocked. 2 O Re ll Tank Power Release Button Figure 1. Tabs Figure 2. 4 44059-01 • 05/11/2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
4
44059-01
•
05/11/2010
Using Your Humidifier
Initial Setup and Operation
2
1. Remove the plastic bag covering from the warm mist humidifier.
2. Unravel and straighten the cord before use.
3. Remove the steam unit from the tank. Hold the steam unit securely and press
the release button just above the power cord on the back of the steam unit and
pull straight up and off. Figure 1.
4. Fill the tank with clean, cool tap water until the water level is is about an inch
from the top of the tank.
DO NOT OVERFILL
.
5. Replace the steam unit in the tank and gently press down until the tabs on the
tank snap into place on the steam unit. Figure 2.
6. When using warm mist medications, fill the medicine cup on the steam unit as
directed by the medicine package.
NOTE: DO NOT
add medication of any type into the water in the tank.
7. Plug the power cord into 110-120 Volts AC outlet protected up to 15 Amps.
The warm mist will produce a gentle flow of steam within a few minutes.
CAUTION: DO NOT
use the warm mist with extension cords.
NOTE:
Protect your floor and furniture by placing the warm mist unit on a non-
metallic, waterproof, heat-resistant surface.
8. If steaming does not start within ten minutes, unplug the steam unit and allow
to cool.
9. Remove the steam unit from the tank and add 2 to 3 pinches of ordinary
table salt to the water and mix thoroughly.
10. Reassemble the unit.
11. If steaming still does not start after another 10 minutes, add another pinch
or two of salt and mix thoroughly. Do not exceed 1/8 teaspon of salt, about
4-5 pinches, as excessive boiling or a blown fuse could occur.
Note:
Remember the amount of salt you added to start the unit steaming. You
will need to add the same amount each time the unit is refilled. Salt has no effect
on the purity of the steam or medication.
12. The warm mist will automatically stop producing steam when the water has
reached the minimum water level.
The refill light will come on to indicate
the unit is out of water. Turn the unit off and refill according to the directions
above.
Caution: ALWAYS
unplug the steam unit and allow to cool before removing
the tank. Never remove the steam unit before it has cooled as you could be
burned or shocked.
Refill Tank
Off
Power
Figure 1.
Figure 2.
Tabs
Release Button