Husqvarna 240 e-series Owners Manual - Page 19
Working Techniques / Maintenance
View all Husqvarna 240 e-series manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
WORKING TECHNIQUES / MAINTENANCE How to avoid kickback WARNING! Kickback can happen very ! suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique. What is kickback? The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object. (44) Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it was being used when the kickback zone of the bar touched the object. Kickback only occurs if the kickback zone of the bar touches an object. (45) Limbing WARNING! A majority of kickback ! accidents occur during limbing. Do not use the kickback zone of the guide bar. Be extremely cautious and avoid contacting the log, other limbs or objects with the nose of the guide bar. Be extremely cautious of limbs under tension. They can spring back toward you and cause loss of control resulting in injury. Make sure that you can stand and move about safely. Work on the left side of the trunk. Work as close as possible to the chain saw for maximum control. If possible, let the weight of the chain saw rest on the trunk. Keep the trunk between you and the chain saw as you move along the trunk. Cutting the trunk into logs See instructions under the heading Basic cutting technique. General The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. Carburetor adjustment Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function • The carburetor governs the engine's speed via the throttle control. Air and fuel are mixed in the carburetor. The air/fuel mixture is adjustable. Correct adjustment is essential to get the best performance from the machine. • The T-screw regulates the throttle setting at idle speed. If the T-screw is turned clockwise this gives a higher idle speed; turning it anti-clockwise gives a lower idle speed. Basic settings and running in The basic carburetor settings are adjusted during testing at the factory. Fine adjustment should be carried out by a skilled technician. Rec. idle speed: See the Technical data section. Fine adjustment of the idling speed T Adjust the idle speed with the T-screw. If it is necessary to re-adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn counterclockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. It should also be good margin to the rpm when the chain starts to rotate. WARNING! Contact your servicing ! dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired. Checking, maintaining and servicing chain saw safety equipment Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer. Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer). Switch off the engine and take off the ignition cable before repairs or maintenance Chain brake and front hand guard Checking brake band wear Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake. (46) Regularly check that the brake band is at least 0.024 inch (0.6 mm) thick at its thinnest point. Checking the front hand guard Make sure the front hand guard is not damaged and that there are no visible defects such as cracks. Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover. (47) 1151508-26 Rev. 1 2009-07-08 English - 19