Husqvarna 330LK Owner Manual - Page 12

To mix gasoline and two-stroke oil, To fill the fuel tank, To do before you operate the product

Get Husqvarna 330LK PDF manuals and user guides View all Husqvarna 330LK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CAUTION: Do not use two- stroke oil for water-cooled outboard engines, also referred to as outboard oil. Do not use oil for four-stroke engines. To mix gasoline and two-stroke oil Gasoline, liter 5 10 15 20 US gallon 1 2 1/2 5 Two-stroke oil, liter 2% (50:1) 0.10 0.20 0.30 0.40 US fl. oz. 2 ½ 6 ½ 12 ⅞ CAUTION: Small errors can influence the ratio of the mixture drastically when you mix small quantities of fuel. Measure the quantity of oil carefully and make sure that you get the correct mixture. 1. Fill half the quantity of gasoline in a clean container for fuel. 2. Add the full quantity of oil. 3. Shake the fuel mixture. 4. Add the remaining quantity of gasoline to the container. 5. Carefully shake the fuel mixture. To fill the fuel tank WARNING: Obey the procedure that follows for your safety. 1. Stop the engine and let the engine become cool. 2. Clean the area around the fuel tank cap. 3. Shake the container and make sure that the fuel is fully mixed. 4. Remove the fuel tank cap slowly to release the pressure. 5. Fill the fuel tank. CAUTION: Make sure that there is not too much fuel in the fuel tank. The fuel expands when it becomes hot. 6. Tighten the fuel tank cap carefully. 7. Clean fuel spillage on and around the product. 8. Move the product 3 m/10 ft or more away from the refueling area and fuel source before you start the engine. Note: To see where the fuel tank is on your product, refer to Introduction on page 2. To do before you operate the product WARNING: Do not use the product without a guard or a guard that is defective. • Examine the work area to make sure that you know the type of terrain. Examine the slope of the ground and if there are obstacles such as stones, branches and ditches. • Do an inspection of the product. • Do the safety inspections, maintenance and service that are given in this manual. CAUTION: Do not mix fuel for more than 1 month at a time. 12 1660 - 003 - 29.09.2021

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
CAUTION:
Do not use two-
stroke oil for water-cooled outboard
engines, also referred to as outboard
oil. Do not use oil for four-stroke
engines.
To mix gasoline and two-stroke oil
Gasoline, liter
Two-stroke
oil, liter
2% (50:1)
5
0.10
10
0.20
15
0.30
20
0.40
US gallon
US fl. oz.
1
2 ½
2 1/2
6 ½
5
12 ⅞
CAUTION:
Small errors can
influence the ratio of the mixture
drastically when you mix small quantities
of fuel. Measure the quantity of oil
carefully and make sure that you get the
correct mixture.
1.
Fill half the quantity of gasoline in a clean
container for fuel.
2.
Add the full quantity of oil.
3.
Shake the fuel mixture.
4.
Add the remaining quantity of gasoline to the
container.
5.
Carefully shake the fuel mixture.
CAUTION:
Do not mix fuel for more
than 1 month at a time.
To fill the fuel tank
WARNING:
Obey the procedure
that follows for your safety.
1.
Stop the engine and let the engine become cool.
2.
Clean the area around the fuel tank cap.
3.
Shake the container and make sure that the fuel
is fully mixed.
4.
Remove the fuel tank cap slowly to release the
pressure.
5.
Fill the fuel tank.
CAUTION:
Make sure that there
is not too much fuel in the fuel tank.
The fuel expands when it becomes
hot.
6.
Tighten the fuel tank cap carefully.
7.
Clean fuel spillage on and around the product.
8.
Move the product 3 m/10 ft or more away from
the refueling area and fuel source before you
start the engine.
Note:
To see where the fuel tank is on your
product, refer to
Introduction on page 2
.
To do before you operate the
product
WARNING:
Do not use the product
without a guard or a guard that is
defective.
•
Examine the work area to make sure that you
know the type of terrain. Examine the slope of
the ground and if there are obstacles such as
stones, branches and ditches.
•
Do an inspection of the product.
•
Do the safety inspections, maintenance and
service that are given in this manual.
12
1660 - 003 - 29.09.2021