Husqvarna 525LST Owners Manual - Page 11

Assembly - blade

Get Husqvarna 525LST PDF manuals and user guides View all Husqvarna 525LST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Fitting the loop handle ASSEMBLY Fitting the trimmer guard and trimmer head • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). B C • Slide the spacer into the slot in the loop handle. Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt. Assembling the cutting equipment WARNING! ! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. A A • Fit the drive disc (B) on the output shaft. • Turn the output shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in the hole to lock the shaft. • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. H H • To dismantle, follow the instructions in the reverse order. WARNING! Never use a cutting ! attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury. 1154519-49 Rev. 4 2013-08-12 English - 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
ASSEMBLY
English
–
11
1154519-49 Rev. 4 2013-08-12
Fitting the loop handle
•
Clip the loop handle onto the shaft. Note that the loop
handle must be fitted between the arrows on the shaft.
•
Slide the spacer into the slot in the loop handle. Fit the
nut, knob and screw. Do not overtighten.
•
Now adjust the trimmer to give a comfortable working
position. Tighten the bolt.
Assembling the cutting
equipment
Fitting the trimmer guard and
trimmer head
•
Fit the correct trimmer guard (A) for use with the
trimmer head. Hook the trimmer guard/combination
guard onto the fitting on the shaft and secure with the
bolt (L).
•
Fit the drive disc (B) on the output shaft.
•
Turn the output shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
•
To dismantle, follow the instructions in the reverse
order.
!
WARNING!
When fitting the cutting attachment it is
extremely important that the raised
section on the drive disc/support flange
engages correctly in the centre hole of
the cutting attachment. If the cutting
attachment is fitted incorrectly it can
result in serious and/or fatal personal
injury.
!
WARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
A
A
B
C
H
H