Husqvarna PW3300 Operation Manual - Page 8

Install Wheel Kit, Moving Pressure Washer, Attach Negative Battery Cable

Get Husqvarna PW3300 PDF manuals and user guides View all Husqvarna PW3300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Install Wheel Kit NOTICE Wheel kit is not intended for over-the-road use. Install the wheel kit as follows: 1. Lift corner of pressure washer and slide caster wheels up into bottom of tubing on each underside of pressure washer frame. 2. Using a 19 mm wrench, turn nut (A) under collar of caster wheels to tighten. 3. Release handle pin and make sure latch (G) locks into place. G 4. Place lock levers on caster wheels in the "Off" postion to unlock wheels and move pressure washer to desired location. A 3. Slide flat washer (B), wheel (C) and another flat washer (B) over axle stud (D). C D t for ction E B o u NOTICE Be sure to install wheel with raised hub inboard. N d 4. Lift corner of pressure washer slightly and slide axle stud through mounting bracket on pressure washer frame. ro 5. Insert retaining pin (E) through hole on axle stud. 6. Repeat steps 3 through 5 to secure second wheel. p Moving Pressure Washer e The pressure washer is equipped with a handle that locks R into three different positions for your convenience. With the NOTICE Always face pressure washer and push or pull to desired location. When moving pressure washer on an incline, always make sure you are uphill from pressure washer. 5. Place lock levers on caster wheels in the "On" postion to lock wheels and keep pressure washer from moving. Attach Negative Battery Cable Your unit is equipped with electric start capability but can be started manually. If you choose not to use the electric start feature, you do not need to connect the negative battery cable. The sealed battery on the pressure washer is pre-installed except for the negative (black) battery cable. WARNING Battery posts, terminals and related accessories contain lead and lead compounds - chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. To install: handle in the upright position, it makes it easy to push or pull your pressure washer to the desired location. With the handle in the middle position, you can tilt the pressure 1. Cut off tie wrap securing loose end of negative (black) cable. washer back. The handle also folds down flat for storage. 2. Using 8 mm wrenches, remove screw (H) and nut (J) 1. Screw handle pin (F) into bracket on left side of frame on negative battery terminal (-) (K). (viewing pressure washer from engine end). F K J H 2. Pull handle pin out and lift handle to desired position. L 3. Slide negative battery cable (L) over screw. 8 www.usa.husqvarna.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Install Wheel Kit
NOTICE
Wheel kit is not intended for over-the-road use.
Install the wheel kit as follows:
1.
Lift corner of pressure washer and slide caster wheels
up into bottom of tubing on each underside of pressure
washer frame.
2.
Using a 19 mm wrench, turn nut (
A
) under collar of
caster wheels to tighten.
3.
Slide flat washer (
B
), wheel (
C
) and another flat washer
(
B
) over axle stud (
D
).
NOTICE
Be sure to install wheel with raised hub inboard.
4.
Lift corner of pressure washer slightly and slide axle stud
through mounting bracket on pressure washer frame.
5.
Insert retaining pin (
E
) through hole on axle stud.
6.
Repeat steps 3 through 5 to secure second wheel.
Moving Pressure Washer
The pressure washer is equipped with a handle that locks
into three different positions for your convenience. With the
handle in the upright position, it makes it easy to push or
pull your pressure washer to the desired location. With the
handle in the middle position, you can tilt the pressure
washer back. The handle also folds down flat for storage.
1.
Screw handle pin (
F
) into bracket on left side of frame
(viewing pressure washer from engine end).
2.
Pull handle pin out and lift handle to desired position.
3.
Release handle pin and make sure latch (
G
) locks into
place.
4.
Place lock levers on caster wheels in the “
Off
” postion
to unlock wheels and move pressure washer to desired
location.
NOTICE
Always face pressure washer and push or pull to
desired location. When moving pressure washer on an incline,
always make sure you are uphill from pressure washer.
5.
Place lock levers on caster wheels in the “
On
” postion
to lock wheels and keep pressure washer from moving.
Attach Negative Battery Cable
Your unit is equipped with electric start capability but can be
started manually. If you choose not to use the electric start
feature, you do not need to connect the negative battery cable.
The sealed battery on the pressure washer is pre–installed
except for the negative (black) battery cable.
To install:
1.
Cut off tie wrap securing loose end of negative (black)
cable.
2.
Using 8 mm wrenches, remove screw (
H
) and nut (
J
)
on negative battery terminal (
—
) (
K
).
3.
Slide negative battery cable (
L
) over screw.
8
www.usa.husqvarna.com
F
G
WARNING
Battery posts, terminals and related
accessories contain lead and lead compounds - chemicals
known to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
H
L
J
K
B
E
C
D
A
Not for
Reproduction