Husqvarna T540 XP II Owner Manual - Page 35

Maintenance

Get Husqvarna T540 XP II PDF manuals and user guides View all Husqvarna T540 XP II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

MAINTENANCE General The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorized service workshop. Carburetor adjustment Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. AutoTune The engine is equipped with AutoTune, so manual adjustment of the carburettor's H and L needles and the T-screw no longer applies. Both needles and the T-screw have been removed. AutoTune is a function that adjusts the carburettor electronically, always resulting in optimal adjustment. WARNING! If the saw chain rotates while ! idling, contact your servicing dealer. Do not use the chain saw until it has been properly adjusted or repaired. Checking, maintaining and servicing chainsaw safety equipment Note! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below we recommend you to contact our servicing dealer. Chain brake and front hand guard Checking brake band wear • Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake. Function • The carburetor governs the engine's speed via the throttle control. Air and fuel are mixed in the carburetor. The air/fuel mixture is adjustable. • The automatic adjustment of the carburettor means that the engine is adapted to local conditions, e.g. the climate, altitude, petrol and the type of 2-stroke oil. This function is controlled by AutoTune. Engine adjustment The following steps should be taken when the chain saw is started for the first time or when outside circumstances change (fuel, altitude, air filter etc.):Start the engine. Accelerate the engine and saw a number of cuts in a thick log (3-5 min.). The chain saw must be run (8,000 - 12,000 rpm) the entire time so that the carburettor can adjust itself. Conditions NOTE! There is an integrated speed governor in the ignition system that limits the maximum speed. When the speed governor is activated, you will get the same sound experience as when the chain saw 4-cycles. • Regularly check that the brake band is at least 0.024 inch (0,6 mm) thick at its thinnest point. Checking the front hand guard • Make sure the front hand guard is not damaged and that there are no visible defects such as cracks. • Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover. English - 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
MAINTENANCE
English
–
35
General
The user must only carry out the maintenance and
service work described in this manual. More extensive
work must be carried out by an authorized service
workshop.
Carburetor adjustment
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
AutoTune
The engine is equipped with AutoTune, so manual
adjustment of the carburettor’s H and L needles and the
T-screw no longer applies. Both needles and the T-screw
have been removed. AutoTune is a function that adjusts
the carburettor electronically, always resulting in optimal
adjustment.
Function
•
The carburetor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburetor. The air/fuel mixture is adjustable.
•
The automatic adjustment of the carburettor means
that the engine is adapted to local conditions, e.g. the
climate, altitude, petrol and the type of 2-stroke oil.
This function is controlled by AutoTune.
Engine adjustment
The following steps should be taken when the chain saw
is started for the first time or when outside circumstances
change (fuel, altitude, air filter etc.):Start the engine.
Accelerate the engine and saw a number of cuts in a thick
log (3-5 min.).
The chain saw must be run (8,000 - 12,000 rpm) the entire
time so that the carburettor can adjust itself.
Conditions
NOTE! There is an integrated speed governor in the
ignition system that limits the maximum speed. When the
speed governor is activated, you will get the same sound
experience as when the chain saw 4-cycles.
Checking, maintaining and
servicing chainsaw safety
equipment
Chain brake and front hand guard
Checking brake band wear
•
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum. Dirt and wear can impair
operation of the brake.
•
Regularly check that the brake band is at least 0.024
inch (0,6 mm) thick at its thinnest point.
Checking the front hand guard
•
Make sure the front hand guard is not damaged and
that there are no visible defects such as cracks.
•
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to
the clutch cover.
!
WARNING! If the saw chain rotates while
idling, contact your servicing dealer. Do
not use the chain saw until it has been
properly adjusted or repaired.
Note! All servicing and repair work on the machine
requires special training. This is especially true of the
machine
′
s safety equipment. If your machine fails any of
the checks described below we recommend you to
contact our servicing dealer.