Husqvarna YTH24V42LS Owners Manual

Husqvarna YTH24V42LS Manual

Get Husqvarna YTH24V42LS PDF manuals and user guides View all Husqvarna YTH24V42LS manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna YTH24V42LS manual content summary:

  • Husqvarna YTH24V42LS | Owners Manual - Page 1
    07002 YTH24V42LS Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine." 532 44 04-29
  • Husqvarna YTH24V42LS | Owners Manual - Page 2
    's recommendation for wheel weights or counterweights. • Keep machine free of grass , leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage
  • Husqvarna YTH24V42LS | Owners Manual - Page 3
    frequently and replace with manufacturer's recommended parts, when necessary. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction labels
  • Husqvarna YTH24V42LS | Owners Manual - Page 4
    • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your tractor. • Follow the instructions under "Maintenance" and "Storage" sections of this owner's manual. WARNING: This tractor is equipped with an internal combustion engine and should not be
  • Husqvarna YTH24V42LS | Owners Manual - Page 5
    on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions). • For battery and battery cable installation see "REPLACING BATTERY" in the "Service and Adjustments" section in this
  • Husqvarna YTH24V42LS | Owners Manual - Page 6
    FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments section of this manual. Verify that the belts are routed correctly. CHECK BRAKE SYSTEM After you learn how to operate your tractor, check to see that the
  • Husqvarna YTH24V42LS | Owners Manual - Page 7
    AND FEET AWAY KEEP AREA CLEAR SLOPE HAZARDS (SEE SAFETY RULES SECTION) FREE WHEEL (Automatic Models only) Failure to follow instructions could result in serious injury or death. The safety alert symbol is used to identify safety information about hazards which can result in death, serious injury
  • Husqvarna YTH24V42LS | Owners Manual - Page 8
    CONTROL - Disengages transmission for pushing or slowly towing the tractor with the engine off. (N) CHOKE CONTROL - Used when starting a cold engine. (P) SERVICE REMINDER / HOUR METER - Indicates when service is required for the engine and mower. (Q) 12-VOLT POWER PORT - Used for 12 volt accessories
  • Husqvarna YTH24V42LS | Owners Manual - Page 9
    sure parking brake will hold tractor secure. C B Fig. 4 STOPPING (See Fig. 5) MOWER BLADES • To stop mower blades, place attachment clutch control position and remove key. Always remove key when leaving tractor to prevent unauthorized use. • Never use the choke to stop the engine. IMPORTANT: LEAVING
  • Husqvarna YTH24V42LS | Owners Manual - Page 10
    use the blade tip looking lawns, mow deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in this section of manual). • With mower
  • Husqvarna YTH24V42LS | Owners Manual - Page 11
    OPERATION TO STOP MOWER BLADES • Disengage attachment clutch control. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 10). S Fig. 10 REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a
  • Husqvarna YTH24V42LS | Owners Manual - Page 12
    section of this manual. NOTE: Service reminder runs when the ignition key is in any position but "STOP". For accurate reading, be sure key remains in the "STOP" position when engine is not running. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped
  • Husqvarna YTH24V42LS | Owners Manual - Page 13
    transmission is now purged and now ready for normal operation. MOWING TIPS • Tire chains cannot be used when the mower housing is attached to tractor. • Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual
  • Husqvarna YTH24V42LS | Owners Manual - Page 14
    /Replace Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) Change Engine Oil (without oil filter) E N Clean Air
  • Husqvarna YTH24V42LS | Owners Manual - Page 15
    , repair the problem immediately. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. BLADE REMOVAL (See Fig. 14) • Raise mower to highest
  • Husqvarna YTH24V42LS | Owners Manual - Page 16
    . Tighten cap onto the tube securely when finished. ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. CLEAN AIR SCREEN Check the crankcase oil level before starting the engine and after each eight (8) hours
  • Husqvarna YTH24V42LS | Owners Manual - Page 17
    up any spilled gasoline. FUEL FILTER CLAMP DECK WASHOUT PORT (See Fig. 19) Your tractor's deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water
  • Husqvarna YTH24V42LS | Owners Manual - Page 18
    position. • Lower attachment lift lever to its lowest position. • Remove mower belt from electric clutch pulley (M). See Mower Drive Belt Removal in "TO REPLACE MOWER BLADE DRIVE BELT" in this section. • Disconnect front link (E) from mower - remove retainer spring and washer. • Go to either side of
  • Husqvarna YTH24V42LS | Owners Manual - Page 19
    24 IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES. • Raise attachment lift lever to highest position. • If necessary, adjust gauge wheels before operating mower as shown in the Operation section of this manual. See Mower Drive Belt Installation in "TO REPLACE MOWER BLADE DRIVE
  • Husqvarna YTH24V42LS | Owners Manual - Page 20
    , see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front
  • Husqvarna YTH24V42LS | Owners Manual - Page 21
    SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT MOWER DRIVE BELT REMOVAL (See Fig. 30) • Park tractor on a level surface. Engage parking brake. • Lower attachment lift lever to its lowest position. • Remove mandrel covers. • Remove any dirt or grass clippings which may
  • Husqvarna YTH24V42LS | Owners Manual - Page 22
    SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 33) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. Remove mower (See "TO REMOVE MOWER" section in this manual). NOTE:
  • Husqvarna YTH24V42LS | Owners Manual - Page 23
    07002 Fig. 37 TRANSMISSION REMOVAL/REPLACEMENT NEGATIVE (BLACK) CABLE Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See "PURGE TRANSMISSION" in the Operation section of this manual. TERMINAL COVER
  • Husqvarna YTH24V42LS | Owners Manual - Page 24
    etc. Store in a clean, dry area. • Clean entire tractor (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). • Lubricate as shown in the Maintenance section of
  • Husqvarna YTH24V42LS | Owners Manual - Page 25
    . 2. Adjust throttle control. 3. Build-up of grass, leaves, trash under mower. 3. Clean underside of mower housing. 4. Dirty air filter. 4. Clean/replace air filter. 5. Low oil level/dirty oil. 5. Check oil level/change oil. 6. Faulty spark plug. 6. Clean and regap or change spark plug
  • Husqvarna YTH24V42LS | Owners Manual - Page 26
    , trash under mower. 7. Clean underside of mower housing. 8. Mower drive belt worn. 8. Replace mower drive belt. 9. Blades improperly installed. 9. Reinstall blades sharp edge down. 10. Improper blades used. 10. Replace with blades listed in parts manual. 11. Clogged mower deck vent holes
  • Husqvarna YTH24V42LS | Owners Manual - Page 27
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 SCHEMATIC SCH12 A AMMETER (OPTIONAL) BATTERY RED RED FUSE WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON
  • Husqvarna YTH24V42LS | Owners Manual - Page 28
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 ELECTRICAL T15S 90 27 2 1 91 99 100 8 22 79 21 34 26 40 28 55 33 30 24 27 42 43 41 25 16 0 60 AM PS 60 45 46 With 12V Outlet Option 103 59 71 29 102 105 28
  • Husqvarna YTH24V42LS | Owners Manual - Page 29
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 ELECTRICAL KEY PART NO. NO. 1 532 16 34-65 2 874 76 04-12 8 532 41 41-25 16 532 17 61-38 21 532 40 02-52 22 532 00 41-52 24 532 40 02-53 25 532 41 28-95 26 532
  • Husqvarna YTH24V42LS | Owners Manual - Page 30
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 CHASSIS 297 208 204 18 15 3 203 336 206 214 14 130 130 130 130 191 207 25
  • Husqvarna YTH24V42LS | Owners Manual - Page 31
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 CHASSIS KEY PART 14 24-32 Air Duct Bracket Pivot Hood Shield Browning Screw 3/8-16 x 3/4 Window Fuel Screw Hex Wsh Hi-Lo 1/4 x 1/2 unc Support Tank Rear Crossmember Screw 10-24 -18 Plate Deck Lift Vent Deck Lift Console Shift Console Insert
  • Husqvarna YTH24V42LS | Owners Manual - Page 32
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 DRIVE 221 213 207 206 92 125 116 160 56 209 26 185 221 184 35 42 197
  • Husqvarna YTH24V42LS | Owners Manual - Page 33
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 DRIVE KEY PART NO. NO. DESCRIPTION 1 Transaxle 5/16-18 x 2-1/2 Gr. 5 80 532 41 00-24 Bracket Strap Torque 92 874 76 05-20 Bolt Fin Hex x 1-1/4 x 10 Ga. 225 532 40 33-19 Keeper Belt Trans. 227 817 49 05-12 Screw 5/16-18 x 3/4
  • Husqvarna YTH24V42LS | Owners Manual - Page 34
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 ENGINE 116 21 20 1 22 14 111 110 18 15 92 28 109 113 91 37 28 37 29 90 SPARK ARRESTER KIT engine-tex_Kawa-2cyl_6_r1 45 69 92 12 86 11 41 42 85 9 87 62 71 70 2 34
  • Husqvarna YTH24V42LS | Owners Manual - Page 35
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 ENGINE KEY PART NO. NO. 1 -----2 532 14 97-23 given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Kawasaki 1-949-460-5688 35
  • Husqvarna YTH24V42LS | Owners Manual - Page 36
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 STEERING ASSEMBLY 26 51 45 1 21 16 13 64 28 28 63 22 60 19 59 58 50 63 35 61 4 15 65 69 50 68 70 65 9 8 67 7 55 78 2 8 6 9 7 55 67 6 14 5 62 14 15 54 66 54 13 13 8 53 Steering-tex_LEGND2_37 36
  • Husqvarna YTH24V42LS | Owners Manual - Page 37
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 STEERING ASSEMBLY KEY PART NO. NO. DESCRIPTION 1 532 41 64-80 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-89 Spindle Asm., LH 5 532 40 30-90 Spindle Asm., RH 6 532 12 49-
  • Husqvarna YTH24V42LS | Owners Manual - Page 38
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 SEAT ASSEMBLY 1 8 7 41 40 88 7 8 10 21 6 37 6 37 2 44 43 21 seat-tex_6.5SL_3 KEY PART NO. NO. 1 532 16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 3 KEY PART NO. NO. 37 873 80 05-00 40 532 42 59-19 41 532 19
  • Husqvarna YTH24V42LS | Owners Manual - Page 39
    . Decal, Replacement Label, Emiss KEY PART NO. NO. 9 532 14 50-05 10 532 41 86-00 - - 532 16 69-60 - - 532 41 08-05 - - 532 41 08-06 - - 532 44 04-29 DESCRIPTION Decal, Battery Dnge/Poi Decal, Pedal Decal, Bypass Pad, Footrest, LH Pad, Footrest, RH Manual, Owner's (English) WHEELS AND TIRES
  • Husqvarna YTH24V42LS | Owners Manual - Page 40
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 MOWER DECK 52 25 34 27 47 32 37 38 24 56 28 24 26 35 54 53 251 55 29 41 40 34 31 42 44 14 45 24 25 33 49 46 30 50 5 51 3 4 23 22 19 48 18 10 8 59 36 1 9 13 12
  • Husqvarna YTH24V42LS | Owners Manual - Page 41
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 MOWER DECK KEY PART NO. NO. 1 575 43 80-01 2 - - 574 79 24-01 DESCRIPTION Nut, 7/16-14 Hex Nyloc Nut 3/8-16 Hex Flg Nyloc Shield, Belt LH Shield, Belt RH Hcs 5/16-18 x 1 Gr. 5 Wash 5/16 Slw Wheel, Gauge Bolt, Shoulder Arm
  • Husqvarna YTH24V42LS | Owners Manual - Page 42
    TRACTOR - MODEL NO. YTH24V42LS (96043012800), PRODUCT NO. 960 43 01-28 MOWER LIFT                 LIFT TEX?   KEY PART NO. NO. 2 532 Link Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY PART NO. NO. 91 532 40 34-07 96 532 19 52-63 97
  • Husqvarna YTH24V42LS | Owners Manual - Page 43
    43 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION TFHOISLDISAALO15NDGEDGORTETEESDLLOINPEE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than
  • Husqvarna YTH24V42LS | Owners Manual - Page 44
    11.30.10 SR Printed in the U.S.A.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
YTH24V42LS
Owner's Manual
532 44 04-29
07002
"This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only.
Do not use any fuel >E10 in this machine."