Husqvarna YTH24V48LS Owners Manual

Husqvarna YTH24V48LS Manual

Get Husqvarna YTH24V48LS PDF manuals and user guides View all Husqvarna YTH24V48LS manuals
Add to My Manuals
Save this manual to your list of manuals

Husqvarna YTH24V48LS manual content summary:

  • Husqvarna YTH24V48LS | Owners Manual - Page 1
    in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 50-54 Please read the owner's manual carefully and make sure you understand the instructions before using the machine. English
  • Husqvarna YTH24V48LS | Owners Manual - Page 2
    understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine / engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause build-up to occur. Clean any oil or fuel
  • Husqvarna YTH24V48LS | Owners Manual - Page 3
    parts, when necessary. • Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution when servicing them. • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction ), not across. • Choose a low ground speed so that you will not
  • Husqvarna YTH24V48LS | Owners Manual - Page 4
    (below 32°F/0°C) Oil Capacity: W/ Filter: 64 oz (2,0L) W/O Filter: 52 oz (1,5L) Spark Plug: NGK BRP4ES (Gap: .030"/0.76mm) Ground Speed (MPH): Forward: Reverse: 0 - 5.2 0 - 2.9 Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: 28 230 U1R Blade Bolt Torque: 45
  • Husqvarna YTH24V48LS | Owners Manual - Page 5
    on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instructions). • For battery and battery cable installation see "REPLACING BATTERY" in the "Service and Adjustments" section in this
  • Husqvarna YTH24V48LS | Owners Manual - Page 6
    DECK LEVELNESS For best cutting results, mower housing should be properly leveled. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. CHECK FOR PROPER POSITION OF ALL BELTS See the figures that are shown for replacing motion and mower blade drive belts in the Service
  • Husqvarna YTH24V48LS | Owners Manual - Page 7
    . Learn and understand their meaning. REVERSE NEUTRAL HIGH LOW CHOKE FAST SLOW IGNITION SWITCH ENGINE OFF REVERSE OPERATION SYSTEM (ROS) ENGINE ON ENGINE START PARKING BRAKE MOWER HEIGHT MOWER LIFT LIGHTS ON FUEL BATTERY REVERSE FORWARD CRUISE CONTROL CLUTCH/BRAKE PEDAL 15 15
  • Husqvarna YTH24V48LS | Owners Manual - Page 8
    and adjustments. Save this manual for future reference. D mower blades transmission for pushing or slowly towing the tractor with the engine off. (N) CHOKE CONTROL - Used when starting a cold engine. (P) SERVICE REMINDER / HOUR METER - Indicates when service is required for the engine and mower
  • Husqvarna YTH24V48LS | Owners Manual - Page 9
    4 STOPPING (See Fig. 5) MOWER BLADES • To stop mower blades, place attachment clutch control in POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY TO BE DISCHARGED, (DEAD). NOTE: Under DRIVE - • To stop ground drive, depress brake pedal into full "BRAKE" position. IMPORTANT: FORWARD AND REVERSE DRIVE
  • Husqvarna YTH24V48LS | Owners Manual - Page 10
    With forward drive pedal depressed to deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See "TO AD- JUST MOWER CUTTING HEIGHT" in this section of manual). • With mower
  • Husqvarna YTH24V48LS | Owners Manual - Page 11
    MOWER BLADES • Disengage attachment clutch control. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping or changing • To reengage transmission, reverse above procedure
  • Husqvarna YTH24V48LS | Owners Manual - Page 12
    service engine and mower, see the Maintenance section of this manual. NOTE: Service reminder runs when the ignition key is in any position but "STOP". For accurate reading, be sure key remains in the "STOP" position when engine is not running. BEFORE STARTING THE ENGINE CHECK ENGINE OIL Instructions
  • Husqvarna YTH24V48LS | Owners Manual - Page 13
    fast position. • The attachments and ground drive can now be used. If the engine Service and Adjustments section of this manual. PURGE TRANSMISSION air inside the transmission which may have developed during shipping of your tractor. IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE
  • Husqvarna YTH24V48LS | Owners Manual - Page 14
    "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut
  • Husqvarna YTH24V48LS | Owners Manual - Page 15
    Mower Blades T Lubrication Chart 0 Check Battery Level R Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) Change Engine Oil (without oil filter) E N Clean Air Filter
  • Husqvarna YTH24V48LS | Owners Manual - Page 16
    must be checked and adjusted. (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See the sides of tires for proper PSI). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps
  • Husqvarna YTH24V48LS | Owners Manual - Page 17
    water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • oil fill cap/dipstick securely each time you check the oil level. TO CHANGE ENGINE OIL (See Fig. 16 - 18) Determine temperature range expected before oil change. All oil must meet API service
  • Husqvarna YTH24V48LS | Owners Manual - Page 18
    washer to clean your tractor unless the engine and transmission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower. FUEL FILTER Fig. 19 CLAMP 18
  • Husqvarna YTH24V48LS | Owners Manual - Page 19
    . 3. Thread the nozzle adapter (packaged with your tractor's Operator's Manual) onto the end of your garden hose. 4. Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck. Release the lock collar to lock the adapter on the
  • Husqvarna YTH24V48LS | Owners Manual - Page 20
    position. • Lower attachment lift lever to its lowest position. • Remove mower belt from electric clutch pulley (M). See Mower Drive Belt Removal in "TO REPLACE MOWER BLADE DRIVE BELT" in this section. • Disconnect front link (E) from mower - remove retainer spring and washer. • Go to either side of
  • Husqvarna YTH24V48LS | Owners Manual - Page 21
    FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES. • Raise attachment lift lever to highest position. • If necessary, adjust gauge wheels before operating mower as shown in the Operation section of this manual. See Mower Drive Belt Installation in "TO REPLACE MOWER BLADE DRIVE BELT" in this section of
  • Husqvarna YTH24V48LS | Owners Manual - Page 22
    , see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 30 & 31) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front
  • Husqvarna YTH24V48LS | Owners Manual - Page 23
    the electric clutch on the engine shaft. MOWER DRIVE BELT INSTALLATION (See Fig. 33 & 34) NOTE: For ease in installing the deck belt, refer to the routing decal on the cutting deck. • Place the belt around all the pulleys except the center spindle pulley. • With a 3/8" breaker bar, shift the idler
  • Husqvarna YTH24V48LS | Owners Manual - Page 24
    SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 35) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - 1. Remove mower (See "TO REMOVE MOWER" section in this manual). NOTE:
  • Husqvarna YTH24V48LS | Owners Manual - Page 25
    battery terminal with remaining bolt and nut. Tighten securely • Close hood. HOOD HEADLIGHT WIRE CONNECTOR 07002 Fig. 39 TRANSMISSION REMOVAL/REPLACEMENT NEGATIVE (BLACK) CABLE Should your transmission require removal for service TO REPLACE HEADLIGHT BULB see engine manual. • Raise hood. • Pull
  • Husqvarna YTH24V48LS | Owners Manual - Page 26
    and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). • Lubricate as shown in the Maintenance section of this manual. • Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage
  • Husqvarna YTH24V48LS | Owners Manual - Page 27
    , trash under mower. 3. Clean underside of mower housing. 4. Dirty air filter. 4. Clean/replace air filter. 5. Low oil level/dirty oil. 5. Check oil level/change oil. 6. Faulty spark plug. 6. Clean and regap or change spark plug. 7. Dirty fuel filter. 7. Replace fuel filter. 8. Stale or
  • Husqvarna YTH24V48LS | Owners Manual - Page 28
    , trash under mower. 7. Clean underside of mower housing. 8. Mower drive belt worn. 8. Replace mower drive belt. 9. Blades improperly installed. 9. Reinstall blades sharp edge down. 10. Improper blades used. 10. Replace with blades listed in parts manual. 11. Clogged mower deck vent holes
  • Husqvarna YTH24V48LS | Owners Manual - Page 29
    . YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 SCHEMATIC SCH12 A AMMETER (OPTIONAL) BATTERY RED RED FUSE SOLENOID BLACK WHITE PTO SWITCH (DISENGAGED) S B M A1 G L NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE
  • Husqvarna YTH24V48LS | Owners Manual - Page 30
    TRACTOR - MODEL NO. YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 ELECTRICAL T15S 90 33 22 30 27 2 1 91 99 100 8 79 21 34 24 27 42 43 41 26 40 25 28 55 16 0 60 AM PS 60 45 46 With 12V Outlet Option 103 59 71 29 30 102 105
  • Husqvarna YTH24V48LS | Owners Manual - Page 31
    NO. YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 ELECTRICAL KEY PART NO. NO. 1 532 16 34-65 2 874 76 04- 5/16-18 x 3/4 TYTT Outlet 12-Volt Harness Ign. Socket Asm Bulb Twistlock Cover Terminal Strap Battery Mount Front Screw Hexwsh Thdrol 1/4-20 x 3/4 Washer 9/32 x 7/8 x 16 Ga. Harness Pigtail
  • Husqvarna YTH24V48LS | Owners Manual - Page 32
    TRACTOR - MODEL NO. YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 CHASSIS 15 208 3 204 297 336 159 346 196 221 203 130 14 214 206 137 234 5 176 176 178 137 234 176 175 177 130 130 25 191 207 18 202 151 205 335 199 162 162 161 176 36 194 36 194 176 182 150 337 130 37 228 130
  • Husqvarna YTH24V48LS | Owners Manual - Page 33
    75-90 Bumper Dash 150 532 43 97-74 Air Duct 151 532 43 66-70 Bracket Pivot Hood Wsh 1/4 x 1/2 unc 165 532 19 43-30 Support Tank Rear 175 532 19 63-04 Crossmember 176 Insert Reflective RH KEY PART NO. NO. DESCRIPTION 194 873 90 05 74 Console Asm Deck Lift 199 532 19 82-59 Plate Deck Lift 202 532
  • Husqvarna YTH24V48LS | Owners Manual - Page 34
    TRACTOR - MODEL NO. YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 DRIVE 74 220 70 74 56 221 213 209 207 206 92 125 116 160 26 185 80 214 284 210 163 215 211 166 222 51 51 183 153 116 2 33 230 205 drive-tex_K46_pedal_70_r2 1 73 99 125 225 116 2 183 73 230 205 33 34
  • Husqvarna YTH24V48LS | Owners Manual - Page 35
    52 532 19 43-26 Idler V-Groove 910" Offset 56 532 13 09-69 V-Belt, Drive 64 532 19 78-65 Shaft Asm. Pedal Brake Control 70 532 43 96-61 52-57 Latch Brake Parking 170 532 41 34-30 Keeper Belt Centerspan 183 532 13 70-57 Spacer Split KEY PART NO. NO. DESCRIPTION 184 532 44 14-55 Handle Parking
  • Husqvarna YTH24V48LS | Owners Manual - Page 36
    parts from engine manufacturer) 2 532 14 97-23 Muffler 9 532 19 43-20 Keeper Belt Engine 11 532 40 00-08 Clutch 12 532 40 50-97 Pulley Engine 14 532 14 84-56 Tube Drain Oil 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Kawasaki
  • Husqvarna YTH24V48LS | Owners Manual - Page 37
    54 66 54 13 13 8 53 Steering-tex_LEGND2_39_r1 KEY PART NO. NO. 1 532 43 97-40 2 532 Spindle Washer 25/32 x 1-1/4 x 16 Ga. Washer, Lock Hvy Hlcl Spr 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Adapter, Wheel Steering Steering Support Deck Susp. Front Washer Thrust NOTE: All component dimensions given
  • Husqvarna YTH24V48LS | Owners Manual - Page 38
    TRACTOR - MODEL NO. YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 MOWER DECK 52 33 24 17 57 25 34 43 45 23 46 16 55 27 51 56 50 19 54 18 32 22 24 5 4 21 6 31
  • Husqvarna YTH24V48LS | Owners Manual - Page 39
    MOWER DECK KEY PART , Clevis 5/16 x 5.19 Blade, 16-1/4" Bolt/Washer Asm, Idler Spec. Hub Arm, Idler, Blk Belt, Deck Guard, Belt Eyebolt 5/16 x 3-1/2 Nut 5/16-18 Hex Whizlk Spring Ball Bearing Pulley Clip Retainer Dia. 290 Rod Anti Sway Washer 13/32 x 13/16 x 12 Ga. Pin Cotter 5/16 Service Deck
  • Husqvarna YTH24V48LS | Owners Manual - Page 40
    YTH24V48LS (96043011602), PRODUCT NO. 960 43 01-16 MOWER LIFT                 LIFT TEX?   KEY PART NO. NO. 2 532 42 20-27 3 532 Link Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY PART NO. NO. 91 532 40 34-07 96 532 19 52-63 97 817
  • Husqvarna YTH24V48LS | Owners Manual - Page 41
    8 7 7 8 41 40 8 10 seat-tex_6.5SL_2 21 44 43 6 37 2 37 21 3 KEY PART NO. NO. DESCRIPTION 1 532 42 40-71 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06- 69-77 Pan, Seat 21 532 17 18-52 Bolt, Shoulder 5/16-18 KEY PART NO. NO. DESCRIPTION 37 873 80 05-00 Nut, Lock 5/16-18 unc 40
  • Husqvarna YTH24V48LS | Owners Manual - Page 42
    -00 Decal, Pedal Husq. Crown 8 532 42 62-09 Decal, Warning Reserve Fuel 8 KEY PART NO. NO. DESCRIPTION 9 532 14 50-05 Decal, Battery Dnge/Poi 10 539 11 32-24 Decal, Warning 11 532 19 87-85 Decal, Deck Sch - - 532 16 69-60 Decal, Bypass - - 532 43 98-82 Pad, Footrest
  • Husqvarna YTH24V48LS | Owners Manual - Page 43
    43 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION TFHOISLDISAALO15NDGEDGORTETEESDLLOINPEE degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2. Hold page
  • Husqvarna YTH24V48LS | Owners Manual - Page 44
    07/20/2011 BD
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
English
532 44 50-54
Owner’s Manual
YTH24V48LS / 96043011602
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
Please read the owner's manual carefully and make sure you
understand the instructions before using the machine.