IBM 2626HNU User Guide - Page 45

Numeric Error Codes, and remedies for reported problems.

Get IBM 2626HNU - ThinkPad 390X 2626 PDF manuals and user guides
UPC - 087944512387
View all IBM 2626HNU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Numeric Error Codes The following is a list of the message that the BIOS can display. Most of them occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured. Following the list are explanations of the messages and remedies for reported problems. If the system fails after you make changes in the Setup menus, reset the computer, enter Setup and install Setup defaults or correct the error. Symptom/Error 0200 Failure Fixed Disk 021x Keyboard error 023x Memory error 0250 System battery error 0251 System CMOS checksum bad - Default configuration used 0260 System timer error 0270 Real time clock error 0271 Check date and time setting FRU/Action in Sequence 1. Reseat hard disk drive. 2. Load Setup Defaults in BIOS Setup Utility. 3. Hard disk drive 4. System board Go to "Keyboard and Auxiliary Input Device Checkout" on page 29. 1. DIMM 2. BIOS ROM 3. System board Replace backup battery (RTC) and run BIOS Setup Utility to reconfigure the system time, then reboot the system. 1. Backup battery (RTC) 2. Run BIOS Setup Utility to recon- figure the system, then reboot the system. 1. Backup battery (RTC) 2. Run BIOS Setup Utility to recon- figure the system, then reboot the system. 3. System board 1. Backtup battery (RTC) 2. Run BIOS Setup Utility to recon- figure the system, then reboot the system. 3. System board 1. Run BIOS Setup Utility and verify date and time. 2. Backup battery (RTC) 3. System board ThinkPad 390X / i 1700 HMM 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
Numeric Error Codes
The following is a list of the message that the BIOS can
display. Most of them occur during POST. Some of them
display information about a hardware device, e.g., the
amount of memory installed. Others may indicate a
problem with a device, such as the way it has been config-
ured.
Following the list are explanations of the messages
and remedies for reported problems.
If the system fails after you make changes in the Setup
menus, reset the computer, enter Setup and install Setup
defaults or correct the error.
Symptom/Error
FRU/Action in Sequence
0200
Failure Fixed
Disk
1.
Reseat hard disk drive.
2.
Load Setup Defaults in BIOS Setup
Utility.
3.
Hard disk drive
4.
System board
021x
Keyboard error
Go to “Keyboard and Auxiliary Input
Device Checkout” on page
29.
023x
Memory error
1.
DIMM
2.
BIOS ROM
3.
System board
0250
System battery
error
Replace backup battery (RTC) and run
BIOS Setup Utility to reconfigure the
system time, then reboot the system.
0251
System CMOS
checksum bad
— Default
configuration
used
1.
Backup battery (RTC)
2.
Run BIOS Setup Utility to recon-
figure the system, then reboot the
system.
0260
System timer
error
1.
Backup battery (RTC)
2.
Run BIOS Setup Utility to recon-
figure the system, then reboot the
system.
3.
System board
0270
Real time
clock error
1.
Backtup battery (RTC)
2.
Run BIOS Setup Utility to recon-
figure the system, then reboot the
system.
3.
System board
0271
Check date
and time
setting
1.
Run BIOS Setup Utility and verify
date and time.
2.
Backup battery (RTC)
3.
System board
ThinkPad 390X / i 1700 HMM
39