Icom FR9010 Fr9010 P25 Network Solutions - Page 4
VHF AND UHF P25 REPEATERS, A Broad P25 Product Lineup, Other Features - ic
View all Icom FR9010 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
VHF AND UHF P25 REPEATERS ias p25 network solutions SPECIFICATIONS IC-FR9000 Series GENERAL Frequency coverage IC-FR9010 146-174MHz IC-FR9020 440-475MHz Number of channels Max. 500 channels Channel spacing 12.5/20/25/30kHz* Type of emission Frequency stability Antenna impedance 16K0F3E*, 11K0F3E, 8K10F1E/F1D ±2.5ppm (W/N) ±1.5ppm (Digital) ±1.5ppm (W/N) ±1.5ppm (Digital) 50Ω (Type-N) Operating temperature range -30˚C to +60˚C; -22˚F to +140˚F Power supply voltage Current drain TX (at 13.6V DC) RX Dimensions (W×H×D) 13.6V DC nominal 16A (High) 18A (High) 3A/280mA (Max. audio/Stand-by) 482×88×413 mm ; 18.98×3.46×16.26 in Weight 11.0kg ; 24.3lb (approximately) TRANSMITTER Output power Max. frequency deviation 110W/50W (High/Low) 100% duty cycle 100W/50W (High/Low) 100% duty cycle ±5.0kHz/±2.5kHz (W/N) Spurious emissions 80dB min. 76dB min. FM hum and noise 55/50dB min. (W/N) Audio harmonic distortion 3% typ. (60% deviation) Microphone impedance 600Ω (8-pin modular) RECEIVER Sensitivity 12dB SINAD 5% BER Adjacent channel selectivity Spurious response Intermodulation rejection Hum and noise ratio 0.30µV typ. 0.30µV typ. 82/76dB min. (W/N) 80/72dB min. (W/N) 55dB min. (Digital) 55dB min. (Digital) 95dB min. (W/N) 85dB min. (W/N) 83dB min. (Digital) 83dB min. (Digital) 79dB min. (W/N) 77dB min. (W/N) 79dB min. (Digital) 77dB min. (Digital) 48dB min. (W/N) Audio output power 7.5W typ. at 5% distortion with 8Ω load Measurements made in accordance with EIA/TIA-603 (for FM) and TIA-102 (for Digital). All stated specifications are subject to change without notice or obligation. * 25kHz bandwidth is no longer available for FCC Part 90 licensees for USA versions. Ask your dealer if you need 25kHz bandwidth. Applicable U.S. Military Specifications Standard High Temperature Low Temperature Vibration Method 501.5 502.5 514.6 MIL 810 G Shock 516.6 Also meets equivalent MIL-STD-810-C, -D, -E and -F. Procedure I, II I, II I I Icom America Systems designs, assembles and installs complete, custom-built communications systems. P25 Channel Controller powered by Etherstack. ©2014 Icom America Inc. The Icom logo is a registered trademark of Icom Inc. Etherstack is a registered trademark of Etherstack. All other trademarks remain the property of their respective owners. All information is subject to change without written notice or obligation. 41675 Program Connector RX Connector (9-Pin) TX/Antenna Connector D-SUB Connector (25-Pin) USB 10MHz Input Fuse DC Input A Broad P25 Product Lineup The IC-F9011 and IC-F9511 series are designed for the P25 terminal components with the following digital features. • P25 conventional • Short message • P25 trunking • Radio check • Individual, group and all calls • Status • Emergency call and alarm • Radio inhibit /uninhibit • Radio monitor • AES/DES encryption (option) • Call alert • OTAR (Over-the-Air-Rekeying) Other Features • 110 W 100% Duty Cycle Operation • P25 Conventional, Analog FM and Mixed Mode • 500 Memory Channels Capacity • P25 Conventional Base Mode • D-SUB 25-pin Accessory Connector • Programmable CTCSS, DTCS and NAC All hardware compatible with standard 19" rack installation • Open racks, cabinets, enclosures are available • Optional accessories available Contact Information phone: fax: e-mail: web: 425.450.6098 425.450.6093 [email protected] www.icomamerica.com/systems