Icom IC-9700 Instruction Manual basic - Page 77

Resetting

Get Icom IC-9700 PDF manuals and user guides View all Icom IC-9700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

MAINTENANCE 10 Resetting Occasionally, erroneous information may be displayed. This may be caused by static electricity or by other factors. If this problem occurs, turn OFF the transceiver. After waiting a few seconds, turn ON the transceiver again. If the problem still exists, perform a Partial reset, as described to the right. If the problem still exists after a Partial reset, perform an All reset, also described to the right. NOTE: An All reset clears all data and returns all settings to their factory defaults. Save memory channel content, setting status, and so on, onto an SD card before an All reset. (p. 10-2) DDPartial reset 1. Open the RESET screen. 1 MENU » SET > Others > Reset 2 2. Touch "Partial Reset." 3 4 ••The confirmation screen is displayed. 5 3. Touch [Yes]. L After the resetting, the default VFO mode screen is 6 displayed. 7 After performing a Partial reset 8 A Partial reset resets operating settings to their default values (VFO frequency, VFO settings, menu contents) 9 without clearing the items listed below: ••Memory channel contents 10 ••Call sign memories ••Message contents ••DTMF memory contents ••GPS memory contents ••Repeater list contents DDAll reset 11 1. Open the RESET screen. MENU » SET > Others > Reset 12 ••Network settings ••REF Adjust 2. Touch "All Reset." 13 ••Fixed Edges ••Allowed call sign list contents 14 After performing an All reset 15 All reset clears all data and returns all settings to their factory defaults. ••The confirmation screen is displayed. 3. Touch [NEXT]. 16 Memory channel contents, filter settings and so on will all be cleared, so you will need to rewrite your 17 operating settings, unless you have a backup. 18 When you cannot enter the Set mode If a touch screen operation error or an unexpected operation occurs, you cannot enter the Set mode. In this case, perform an All reset, as described below: 1. Turn OFF the transceiver. 2. While holding down PBT and V/M , push POWER . 19 20 4. After carefully reading the displayed message, touch [YES] to perform the All reset. LAfter the resetting, the default VFO mode screen is 21 displayed. 10-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
10
MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
10-2
Resetting
Occasionally, erroneous information may be
displayed. This may be caused by static electricity or
by other factors.
If this problem occurs, turn OFF the transceiver. After
waiting a few seconds, turn ON the transceiver again.
If the problem still exists, perform a
Partial reset,
as
described to the right.
If the problem still exists after a Partial reset, perform
an
All reset,
also described to the right.
NOTE:
An All reset clears all data and returns all settings
to their factory defaults. Save memory channel content,
setting status, and so on, onto an SD card before an All
reset. (p. 10-2)
After performing a Partial reset
A Partial reset resets operating settings to their default
values (VFO frequency, VFO settings, menu contents)
without clearing the items listed below:
• Memory channel contents
• Call sign memories
• Message contents
• DTMF memory contents
• GPS memory contents
• Repeater list contents
• Network settings
• REF Adjust
• Fixed Edges
• Allowed call sign list contents
After performing an All reset
All reset clears all data and returns all settings to their
factory defaults.
Memory channel contents, filter settings and so on
will all be cleared, so you will need to rewrite your
operating settings, unless you have a backup.
D
Partial reset
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2.
Touch “Partial Reset.”
•
The confirmation screen is displayed.
3.
Touch [Yes].
L
After the resetting, the default VFO mode screen is
displayed.
D
All reset
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2.
Touch “All Reset.”
•
The confirmation screen is displayed.
3.
Touch [NEXT].
4.
After carefully reading the displayed message,
touch [YES] to perform the All reset.
L
After the resetting, the default VFO mode screen is
displayed.
When you cannot enter the Set mode
If a touch screen operation error or an unexpected
operation occurs, you cannot enter the Set mode. In
this case, perform an All reset, as described below:
1.
Turn OFF the transceiver.
2. While holding down
PBT
and
V/M
, push
POWER
.