Icom IC-A25N Navigation Guide - Page 2

Bluetooth® OPERATION (Continued) DDPairing with a Low Energy device Pair a Low Energy (LE) device, as shown below. 1. Push [MENU]. 2. Select "LE Device," and then push [ENT]. (Bluetooth > Pairing/Connect > Search Device > LE Device) 3. Perform pairing from the LE device within 2 minutes. L The remaining time is displayed. DDBluetooth module specifications ••Frequency range: 2402 ~ 2480 MHz ••Transmission power: 4 dBm (Typical) ••Version: 4.2 ••Support profile: HFP, HSP, SPP, HRP, GATT (GATT over Serial) KEYS USED FOR NAVIGATION FUNCTION Push [F], and then push another key to use the secondary functions listed below. DDDisconnecting a paired device You can disconnect a paired Bluetooth device if it is not used. 1. Push [MENU]. 2. Select "Pairing/Connect." (Bluetooth > Pairing/Connect) ••Paired devices are displayed. L"(Connect)" is displayed, if a device is connected. 3. Select a device to disconnect, and then push [ENT]. ••The screen as shown to the right is displayed. 4. Push [ENT].* *A confirmation dialog is displayed. 5. Push [MENU] to return to the Main screen. DDUnpairing a device Before unpairing a connected headset or device, disconnect it. 1. Push [MENU]. 2. Select "Pairing/Connect." (Bluetooth > Pairing/Connect) ••Paired devices are displayed. 3. Select a device to disconnect, and then push [ENT]. ••The screen as shown to the right is displayed. 4. Select "Unpair," and then push [ENT].* *A confirmation dialog is displayed. 5. Push [MENU] to return to the Main screen. DDBluetooth settings You can customize the Bluetooth settings on the "Settings" screen. Refer to The FULL MANUAL for details. ([MENU] > Bluetooth > Settings) q w e t r q OMNI BEARING SELECTOR [1]/[OBS] Push to enter the Omni Bearing Selector (OBS) mode, to set the course heading. w TO/FROM SELECTOR KEY [2]/[TO FROM]  Push to change the "TO/FROM" indicator and invert the OBS setting on the Course Deviation Indicator (CDI) screen. e WAYPOINT NAVIGATION KEY [4]/[WPT NAV] Push to display the Waypoint Navigation screen.* *Only when a waypoint or a flight plan is selected. r DIRECT-TO KEY [5]/[ ] Push to display the "Direct-To WPT" screen, to enter a waypoint. t FLIGHT PLAN KEY [6]/[FPL] Push to display the current flight plan.* *Only when a flight plan is selected. - 2 - VOR NAVIGATION DDCourse Deviation Indicator (CDI) screen The transceiver displays the CDI screen when the NAV band frequency is selected. DDFlying to a VOR station 1. Select a VOR station's frequency. ••The CDI screen is displayed. y q w t r e q COMPASS ROSE w COURSE DEVIATION NEEDLE Displayed when a VOR signal is received. e DEVIATION MARKS r OBS VALUE INDICATOR Displays the course heading. t VOR VALUE INDICATOR Displays the heading to or from a VOR. y TO/FROM INDICATOR DDUsing the Omni Bearing Selector (OBS) Use the Omni Bearing Selector, as shown below, to set the course heading. 1. Push [F], and then push [OBS] to enter the OBS mode. ••The OBS value is highlighted. 2. Rotate [DIAL], or push keypad keys to set the course heading. 2. Push [F], and then push [OBS] to enter the OBS mode. ••The OBS value is highlighted. ••The Course deviation is displayed, as shown to the right. 3. Push [ENT]. 4. Confirm the TO/FROM indicator displays "TO." LIf "FROM" is displayed, push [F], and then push [TO FROM] to display "TO." 5. Maintain the heading that the Course Deviation Needle comes to the center of CDI. NOTE: The IC-A25N and IC-A25NE's VOR Navigation features are supplemental aids to navigation only, and are not intended to be a substitute for primary VOR navigation equipment. 3. Push [ENT] to save the adjusted course heading. - 3 -