Icom IC-FR5000 Trunking/network Controller - Page 2

INSTALLATION DDInstalling the UC-FR5000 Install the controller into the channel module using six of the seven supplied 3 × 8 mm screws. NOTE: BE SURE to match the holes in the controller to the projections on the channel module's chassis. Controller DDAttaching the rear panel 1. Attach the supplied rear panel to the rear panel holder using one of the seven supplied 3 × 8 mm screws. 2. Attach the rear panel and holder set to the channel module using the three supplied 3 × 8 mm screws. Channel module q Holes Rear panel w Rear panel holder Projections Channel module TIP: If you have installed a channel extension module (optional UR-FR5000/UR-FR6000 series), an additional controller in it enables you to control each channel module from a PC in the Conventional/Trunking operation mode. DDConnecting the flat cable NOTE: BE SURE to insert the flat cable with the metal strips facing the edge of the Printed Circuit Board (PCB), and not the opposite way. 1. Turn the channel module upside down. Insert one end of the flat cable into J8 on the PCB of the channel module. Then, carefully pass the flat cable through the opening of the channel module's chassis to the top side. SUPPLIED ACCESSORIES Rear panel Rear panel holder Flat cable Screws (3 × 8 mm) Screws (3 × 12 mm) Dust protectors CF card* Connector caps Bottom Front Flat cable Rear Top J8 *Not supplied, depending on the controller's version. OPTION Opening 2. Turn over the channel module. Carefully pull out the other end of the flat cable from the opening, and then insert it into J1 on the controller. Top Front J1 Flat cable CF-FR5000MC cf card Upgrades the UC-FR5000 #01 to enable Multi Site Conventional mode operation. Same as that supplied with UC-FR5000 #02. CF-FR5000MT cf card Upgrades the UC-FR5000 #01 to enable Multi Site Conventional/Trunking mode operation. Same as that supplied with UC-FR5000 #03. Rear Bottom Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. JavaScript is a registered trademark of Sun Microsystems, Inc. All other products or brands are registered trademarks or trademarks of their respective holders. - 2 - ASSEMBLING THE UNIT 1. Reattach the top and bottom covers of the channel module, and then tighten all the screws. Channel module 2. R einstall the channel module and the screws to their original positions, and then connect the control cable of the repeater's front panel to the channel module. Channel module Control cable CONNECTION NOTE: ••CAT-5 straight cables are required for connection. (User supplied) ••BE SURE to cover each connected cable with a supplied dust protector. Even if the cable has its own cover, replace it with the supplied dust protector. ••KEEP the supplied connector caps attached when the connectors are not in use, to avoid getting bad contacts from dust and moisture. Each controller has a LAN connector and two BUS connectors. q [LAN] connector For an Ethernet connection. Connect the controller to an Ethernet (LAN) port of a PC. In the Trunking mode, the controller at one end of the chain must be connected. You can control the controller and all others in the chain from the PC. w [BUS] connectors (BUS-1, BUS-2) For data communication between the controllers in the Trunking mode, either BUS-1 or BUS-2 can be used. They enable the controllers to be "daisy-chained" together, and form a network that allows trunking and other data to pass among them. L The illustration below describes one example of a connection for the Trunking mode. PC Front panel P0 P1 P2 P3 P4 Repeater 3. R eattach the top cover of the repeater, and then tighten the seven screws for the top and the two screws on both sides of the repeater. Top cover Repeater w BUS-1 BUS-2 LAN q Connector cap Dust protector Channel extension module P0 P1 P2 P3 P4 Repeater Up to 30 channel modules with controllers can be daisy-chained. Icom is not responsible for the destruction or damage to the Icom transceiver, if the malfunction is because of: • Force majeure, including, but not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. • The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. - 3 -