Icom IC-V10MR Instructions - Page 2

 Before connecting the cable to the PC, OPC-478UC, Program, NEVER

Get Icom IC-V10MR PDF manuals and user guides View all Icom IC-V10MR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

 Before connecting the cable to the PC To use the OPC-478UC PROGRAMMING CABLE, you must first install a USB driver. The latest USB driver and installation guide can be downloaded from the Icom website (https://www.icomjapan.com/support/firmware_driver/). Read the guide carefully before installing the driver.  Connecting the cable 1. Rotate [VOL] to turn OFF the transceiver. 2. Connect the cable as shown below. 3. Rotate [VOL] to turn ON the transceiver.  Reading and entering data To prevent data loss, read all the transceiver's data before entering or editing parameters by using the software, even if the transceiver is factory fresh. Click , or in the top menu of the software, and then select "Read ← TR" to start reading. ● While reading or writing entered data, NEVER turn OFF the transceiver or the PC, and NEVER disconnect the cable. Otherwise, the data could be lost or corrupted. ● Before reading or entering data, make a backup file on your PC. A backup file enables you to easily restore if the data in the transceiver is accidentally deleted. TIP: Refer to the software's Help file for assistance with the functions or settings. To open the Help file, click in the top menu of the software and select "Contents," or simply push the [F1] key on the PC's keyboard. Icom, Icom Inc. and Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. Jun. 2021 A7624-2EX-1 © 2020-2021 Icom Inc.

  • 1
  • 2
Before connecting the cable to the PC
To use the
OPC-478UC
PROGRAMMING CABLE, you must first install a USB driver.
The latest USB driver and installation guide can be downloaded from the Icom website
Read the guide carefully before installing the driver.
Connecting the cable
1. Rotate [VOL] to turn OFF the transceiver.
2. Connect the cable as shown below.
3. Rotate [VOL] to turn ON the transceiver.
Reading and entering data
To prevent data loss, read all the transceiver’s data
before entering or editing parameters by using the
software, even if the transceiver is factory fresh.
Click
, or <
Program
> in the top menu of the
software, and then select “Read ← TR” to start reading.
●
While reading or writing entered data,
NEVER
turn
OFF the transceiver or the PC, and
NEVER
disconnect the cable. Otherwise, the data could be
lost or corrupted.
●
Before reading or entering data, make a backup file
on your PC.
A backup file enables you to easily restore if the data
in the transceiver is accidentally deleted.
TIP:
Refer to the software’s Help file for assistance
with the functions or settings.
To open the Help file, click <Help> in the top menu of
the software and select “Contents,” or simply push the
[F1] key on the PC’s keyboard.
Icom, Icom Inc. and Icom logo are registered
trademarks of Icom Incorporated (Japan) in Japan, the
United States, the United Kingdom, Germany, France,
Spain, Russia, Australia, New Zealand, and/or other
countries.
Microsoft and Windows are registered trademarks of
Microsoft Corporation in the United States and/or other
countries.
All other products or brands are registered trademarks
or trademarks of their respective holders.
Jun. 2021
A7624-2EX-1
© 2020-2021 Icom Inc.