Icom IC-V80 Instruction Manual - Page 57

Trouble Shooting

Get Icom IC-V80 PDF manuals and user guides View all Icom IC-V80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

13 TROUBLE SHOOTING If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 1 PROBLEM POSSIBLE CAUSE SOLUTION REF. 2 The transceiver does not turn • The battery is exhausted. ON. • The battery polarity is reversed. • Charge the battery pack, or replace the batteries. pp. 11-13 • Check the battery polarity. p. 13 3 • Loose connection of a battery pack/case. • Clean battery terminals. p. 13 4 No sound comes from the • Volume is too low. • Rotate [VOL] to adjust to a desired level. p. 14 speaker. • An external speaker or a cloning cable is • Check the external speaker connection or remove - 5 connected to the [SP] jack. the cloning cable. 6 Transmitting is impossible. • The battery is exhausted. • TX permission is inhibited. • Charge the battery pack, or replace the batteries. pp. 11-13 • Set the TX permission setting to "ON" in the Set mode. p. 41 7 Transmitting using the VOX • The VOX gain is set to OFF or too low. • S et the VOX gain to a suitable level. pp. 41, 53 8 function is impossible. • The microphone gain is too low. • Set the microphone gain to a suitable level. p. 41 9 Contacting with another sta- • A different tone or code is used for the • Check the tone/DTCS by performing a tone scan. p. 34 tion is impossible. tone/DTCS squelch. 10 Frequency cannot be set. • The key lock function is activated. • Push [FUNC](M), then push and hold [ ] p. 18 11 (# ENT) for 1 sec. to cancel the key lock function. • The memory mode, Call channel mode, or • Push [VFO/MR/CALL] several times to select the p. 15 12 weather channel mode is selected. VFO mode. 13 A programmed scan does not • The memory mode, Call channel mode, or • Push [VFO/MR/CALL] several times to select the p. 15 start. weather channel mode is selected. VFO mode. 14 • The same frequency has been programmed • Program different frequencies in the scan edge p. 25 in the scan edge channels, "XA"-"Xb." channels. 15 A memor y scan do e s n o t • The VFO mode or Call channel mode is • Push [VFO/MR/CALL] several times to select the p. 15 16 start. selected. memory mode. • Only one or no memory channel has been • Program 2 or more memory channels. p. 25 17 programmed. 18 The displayed frequency is er- • The CPU has malfunctioned. roneous. • External factors have caused a fault. • Reset the transceiver. • Remove and re-attach the battery pack/case. p. 49 p. 2 19 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
50
12
13
13
TROUBLE SHOOTING
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
The transceiver does not turn
ON.
• The battery is exhausted.
• The battery polarity is reversed.
• Loose connection of a battery pack/case.
• Charge the battery pack, or replace the batteries.
• Check the battery polarity.
• Clean battery terminals.
pp. 11–13
p. 13
p. 13
No sound comes from the
speaker.
• Volume is too low.
• An external speaker or a cloning cable is
connected to the
[SP]
jack.
• Rotate
[VOL]
to adjust to a desired level.
• Check the external speaker connection or remove
the cloning cable.
p. 14
–
Transmitting is impossible.
• The battery is exhausted.
• TX permission is inhibited.
• Charge the battery pack, or replace the batteries.
•
Set the TX permission setting to “ON” in the Set mode.
pp. 11–13
p. 41
Transmitting using the VOX
function is impossible.
• The VOX gain is set to OFF or too low.
• The microphone gain is too low.
•
Set the VOX gain to a suitable level.
•
Set the microphone gain to a suitable level.
pp. 41, 53
p. 41
Contacting with another sta-
tion is impossible.
• A different tone or code is used for the
tone/DTCS squelch.
• Check the tone/DTCS by performing a tone scan.
p. 34
Frequency cannot be set.
• The key lock function is activated.
• The memory mode, Call channel mode, or
weather channel mode is selected.
• Push
[FUNC](
M
),
then push and hold
[
]
(# ENT) for 1 sec. to cancel the key lock function.
• Push
[VFO/MR/CALL]
several times to select the
VFO mode.
p. 18
p. 15
A programmed scan does not
start.
• The memory mode, Call channel mode, or
weather channel mode is selected.
• The same frequency has been programmed
in the scan edge channels, “XA”–“Xb.”
• Push
[VFO/MR/CALL]
several times to select the
VFO mode.
• Program different frequencies in the scan edge
channels.
p. 15
p. 25
A memory scan does not
start.
• The VFO mode or Call channel mode is
selected.
• Only one or no memory channel has been
programmed.
• Push
[VFO/MR/CALL]
several times to select the
memory mode.
• Program 2 or more memory channels.
p. 15
p. 25
The displayed frequency is er-
roneous.
• The CPU has malfunctioned.
• External factors have caused a fault.
• Reset the transceiver.
• Remove and re-attach the battery pack/case.
p. 49
p. 2
1
2
3
4
5
6
7
8
9
10
11
14
15
16
17
18
19