Image Fitness 1250 Treadmill English Manual - Page 24

Unplug The Power Cord

Get Image Fitness 1250 Treadmill PDF manuals and user guides View all Image Fitness 1250 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

PROBLEM: The walking belt is off-center SOLUTION: a. If the walking belt has shifted to the left, first re- a move the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjust- ment bolt clockwise, and the right bolt counterclock- wise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered. b. If the walking belt has shifted to the right, first remove the key and UNPLUG THE POWER CORD. b Using the allen wrench, turn the left rear roller adjust- ment bolt counterclockwise, and the right bolt clock- wise, 1/4 of a turn each. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered. c. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the c allen wrench, turn both rear roller adjustment bolts clockwise 1/4 of a turn. When the walking belt is cor- rectly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and carefully walk on the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened. PROBLEM: The Speed/Minutes-Mile display on the console does not function properly SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the Screws (not shown) from the Motor Hood (39). Carefully remove the Motor Hood. Locate the Reed Switch (17) and the Magnet (12) on the left side of the Pulley (11). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that 1/8Ó the gap between the Magnet and the Reed Switch is 43 11 about 1/8Ó. If necessary, loosen the Screw (43) and move the Reed Switch slightly. Retighten the Screw. 17 12 Reattach the Motor Hood (39) and run the treadmill for a few minutes to check for a correct speed reading. Top View 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
PROBLEM:
The walking belt is off-center
SOLUTION:
a.
If the walking belt has shifted to the left,
first re-
move the key and
UNPLUG THE POWER CORD
.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b.
If the walking belt has shifted to the right,
first re-
move the key and
UNPLUG THE POWER CORD
.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
c.
If the walking belt slips when walked on, first remove
the key and
UNPLUG THE POWER CORD
. Using the
allen wrench, turn both rear roller adjustment bolts
clockwise 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side of
the walking belt 3 to 4 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key and carefully walk on
the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
PROBLEM:
The Speed/Minutes-Mile display on the console does not function properly
SOLUTION:
a.
Remove the key from the console and
unplug the power cord.
Remove the Screws (not shown) from the Motor Hood (39). Carefully remove the Motor Hood.
Locate the Reed Switch (17) and the Magnet (12) on the
left side of the Pulley (11). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure that
the gap between the Magnet and the Reed Switch is
about 1/8².
If necessary, loosen the Screw (43) and
move the Reed Switch slightly. Retighten the Screw.
Reattach the Motor Hood (39) and run the treadmill for a
few minutes to check for a correct speed reading.
b
c
12
17
43
1/8³
11
Top
View
a
24