Insignia NS-AHBTOENC Quick Setup Guide - Page 1

QUICK SETUP GUIDE Insignia Noise-Canceling Over-Ear Headphones NS-AHBTOENC/NS-AHBTOENC-C PACKAGE CONTENTS • Bluetooth Noise-Canceling Headphones • 3.5 mm audio cable • USB charging cable • Quick Setup Guide FEATURES • Noise canceling technology helps block out external noise • Bluetooth lets you make wireless connections • Rechargeable battery provides up to 20 hours of music playback with ANC, or up to 40 hours without ANC • Built-in microphone to make phone calls • Foldable design allows for easy, compact storing • Earcup controls adjust volume and change audio tracks Before using your new product, please read these instructions to prevent any damage. Front view Right side view L R Left side view Monitor button Monitor LED Indicator LED (Power/Pairing/Play/Pause) button Noise Canceling LED Noise canceling (ANC) button 3.5 mm audio jack Monitor/ANC microphone Touchpad R L R Micro USB port Charging LED Microphone BLUETOOTH AND NOISE CANCELING BASIC INDICATION ACTION Power on OPERATION Press and hold the (power button) more than two seconds. Power off Press and hold the (power button) more than three seconds. Pairing mode Press and hold the (pairing button) more than four seconds in power off mode. Noise canceling on Noise canceling off Play/Pause Volume Up/Down Press and release the ANC (Active Noise-Canceling) button to enter the ANC mode. Press and release the ANC button to exit the ANC mode. Double-tap the touch pad with one finger or press and release the button. From the middle of the touchpad, slide a finger towards + or -. LED INDICATION Blue LED lights for 1.5 seconds Red LED lights for 1.5 seconds Blue and red LEDs blink alternately Green LED on Green LED off LED off LED off Next/Previous track From the middle of the touchpad, slide a finger towards < or >. Answer call Double-tap the touch pad with one finger or press and release the when a call is incoming. Ending call Double-tap the touch pad with one finger and release the touch pad or press and release the when a call is finished. Reject call Long hold the touch pad or press the for more than two seconds, then release when a call is incoming. Redial Double-press the to redial the last phone number. Monitor on Press and release the monitor button to enter the monitor mode. When the monitor mode is off, press and hold the touch pad with your palm or more than two fingers to enter monitor mode. Monitor off Press and release the monitor button to exit the monitor mode. Voice assistant Press and hold the touch pad with one finger for two seconds to hear the voice assistant. 3.5 mm audio jack 3.5 mm audio cable connection to the phone or computer to listen to music when power off. Micro USB port Plug the micro USB connector into this port to charge your headphones. LED off LED off LED off LED off LED off Orange LED on Orange LED off LED off LED off Charging LED on SOUND "Power on" "Power off" Two short beeps "ANC on" "ANC off" Two high beeps for maximum volume One long beep Two long beeps Two long beeps Two short beeps "Monitor on" "Monitor off" CHARGING YOUR HEADPHONES • When the red indicator LED blinks three times every five minutes and the voice prompt says"battery low,"you need to charge the battery. Plug the charging cable into your computer or adapter and into the micro USB port on your headphones. The red LED turns on to indicate that the battery is charging and turns off when fully charged. USING WITH THE 3.5 MM AUDIO CABLE You can use your headphones with non-Bluetooth enabled devices or on airplanes (in which the use of Bluetooth may be restricted) by taking advantage of the headphones' audio jack. • Connect the 3.5 mm end of the included audio cable to the headset's audio jack and the 3.5 mm end to the audio device's headphone jack. Notes: • Corded operation does not require battery power for music listening. • The Bluetooth, microphone, and digital sound enhancement will not work via the audio cable. • Finish your call before connecting to the audio jack. USING YOUR HEADPHONES Turning your headphones on and off 1 Place the headphones around your head. 2 Press and hold (power button) more than two seconds. The LED blinks blue (when turned on) or red (when turned off) and the voice prompt says"Power on"or"Power off". PAIRING YOUR HEADPHONES Notes: • Range is 33 feet (10 meters) • Prompts you by saying "Your device is connected," when connected • Supports easy pairing • Supports a battery indicator icon on an iOS device Pairing with a cell phone or MP3 player 1 With your headphones turned off, press and hold (pairing button) for four seconds. The blue and red LEDs blink alternately. 2 On your phone or MP3 player, select INSIGNIA NS-AHBTOENC from the list of discovered devices, then enter the password 0000 (four zeros) (if required) to pair your headphones. For more information on pairing Bluetooth devices to your cell phone or MP3 player, see the device's documentation. Note: After your headphones have been successfully paired with the cell phone or MP3 player, your headphones will automatically reconnect to the phone or MP3 player.