Insignia NS-AHBTSPORT2 Quick Setup Guide - Page 1

QUICK SETUP GUIDE Wireless Sport Earbuds NS-AHBTSPORT2 PACKAGE CONTENTS • Wireless sport earbuds with earhooks • USB charging cable • Extra small and large ear tips • Quick Setup Guide FEATURES • Ear clips for added security and more secure fit • Up to six hours of music playback • Sweatproof • Microphone to make phone calls • Compatible with most devices that have Bluetooth capability volume-/ volume+/ Previous song Next song LED light POWER/ MFB button USB port for charging Before using your new product, please read these instructions to prevent any damage. CHANGING YOUR EARBUDS 1 Grip the earbud in one hand and the ear tip in the other, then twist and pull to remove the ear tip from the ear bud. Repeat for the other ear bud. 2 Select the correct size ear tips for your ears. 3 Still holding the ear bud in one hand, place the new ear tip over the ear bud and press together until joined. Repeat for the other ear bud. CHARGING YOUR EARBUDS • The red indicator LED blinks twice fast every 20 seconds when the battery is low and you hear"battery low."To charge the battery, plug the microUSB charging cable into your computer and into the microUSB port on your earbuds. The red LED turns on to indicate that the battery is charging and turns off when fully charged. Note: Earbuds will charge whether the power is on or off. However, when charging, it will stop playing music and power off. USING YOUR EARBUDS Turning your earbuds on and off • To turn on your earbuds, press and hold the MFB button for two seconds. The LED blinks red for two seconds and you hear "power on." • To turn off your earbuds, press and hold the MFB button for four seconds. The LED blinks red for two seconds and you hear "power off." BASIC ACTIONS AND INDICATIONS ACTION Charging Charging full Power on Power off Pairing mode Play/Pause Volume Up/Down OPERATION LED INDICATION Red light is on Lights are off Press and hold the MFB for two Red LED on two seconds seconds Press and hold the MFB for four Red LED on two seconds seconds Press and hold the MFB button Blue and red LED blinking for more than five seconds in alternately power off mode Press and release the MFB button Blue LED blinking once every five seconds Press and release the volume up Blue LED blinks once every five or down button seconds Next Track/ Press and hold the volume up or Blue LED blinks once every five Previous Track down button for two seconds seconds Incoming call Blue LED blinks twice every one second Answer call Press and release the MFB Blue LED blinks once every five button when a call is incoming seconds Reject call Press and hold the MFB button Blue LED blinks once every five for two seconds when seconds a call is coming in Reset device list Press and hold the MFB button more than eight seconds in power off mode During the reset, the blue and red LEDs turn on at the same time. When the reset is complete, your earbuds enter pairing mode and the blue and red LED blink alternatively. Disconnect the connected mobile phone Press and hold the volume up and volume down buttons for more than two seconds. The connected mobile phone is disconnected and your earbuds enter pairing mode. Red/blue LED fast flash alternately SOUND "power on" "power off" "your device is connected" One beep when you reach maximum or minimum volume Ring tone "your device is disconnected" PAIRING YOUR EARBUDS Notes: • Range is 33 feet (10 meters) • Supports easy pairing Pairing with a cell phone or MP3 player 1 With your earbuds turned off, press and hold the MFB button for five seconds. The blue and red LEDs blink alternately. 2 On your phone or MP3 player, select NS-AHBTSPORT2 from the list of discovered devices. 3 If required, enter the password 0000 (four zeros) to pair your earbuds. For more information on pairing Bluetooth devices to your cell phone or MP3 player, see the device's documentation. Note: After the earbuds have been successfully paired with the cell phone or MP3 player, the earbuds will automatically reconnect to the phone or MP3 player. Pairing with a computer running Windows Note: Before you pair the earbuds with the computer, make sure that the computer is equipped with Bluetooth. Refer to the computer's documentation or contact the computer manufacturer for more information. If your computer is not Bluetooth compatible, install a Bluetooth USB adapter (dongle). 1 Turn on Bluetooth on the computer. For instructions, see the computer's documentation or contact the computer manufacturer. 2 Double-click the Bluetooth icon in the system tray, then click Add a device. 3 With the earbuds turned off, press and hold the MFB button for five seconds. The LED blinks blue and red alternately. Pairing mode is activated. 4 Double-click the NS-AHBTSPORT2 icon on the computer or highlight the icon, then click Next. Note: If you are unable to locate the NS-AHBTSPORT2 icon, click the Search Again button. 5 If required, enter 0000 (four zeros) in the Bluetooth security code field, then click Next. 6 After the earbuds have been paired, click Close.