Insignia NS-L7HTV-1 Quick Setup Guide (English) - Page 2

Step 4, Step 5, Step 6, Step 3, Step 2 - tv

Page 2 highlights

Step 2 Install the remote control battery Remove the battery holder from the back of the remote control by inserting a fingernail into the groove and pulling out the holder. Place a CR2025 battery with the + side up on the holder. Insert the holder into the remote control. 1 2 Note: The coin-shaped battery is already in the remote control. The first time you use the remote control, remove the plastic sheet from the bottom of the battery to activate the remote. Step 3 Connect the AC adapter Connect the AC adapter into the DC IN jack on the right side of your unit, then connect the AC adapter to a 100-240V power outlet. Step 4 Charging the built-in battery Note: There is no standby mode for this TV, because it runs on a rechargeable battery. Turn off your TV before charging the battery. Connect the supplied AC adapter. Charging starts, and the POWER ON/CHG indicator is red. When the charging is completed, the indicator turns off. Note: On initial use of the TV, charge the battery for 6 hours. Step 5 Establish a signal Make sure that the included rod antenna or a stronger HDTV antenna (not included) is attached to the input at the top of the TV. Extend the antenna rod and move the TV to a location where it can receive the strongest signal, free of obstructions and interference from other devices. Press TV on your remote control to ensure you are in TV mode. Step 6 Scan for channels Note: See your User Guide for more information on connecting your TV directly to cable or satellite service and for scanning for radio stations. To scan for channels when the TV signal source is Antenna Press MENU on the remote control, using the buttons to highlight (channel icon). The Channel menu opens. Press Antenna/Cable Auto Channel Search Add/Skip Channels Antenna OK/ENTER or to enter the Channel menu. Press the buttons to select Auto Channel Search, then press OK/ENTER or to enter the Auto Channel Search menu. Start to Scan is highlighted. Press OK/ENTER or to start the scan. Favorites Channel No. Channel Label Select OK:Enter 80.3 PBS1DTV Menu:Exit If the Automatic Channel Search does not locate the channels you were expecting, try moving the TV to a location where you can pick up a stronger signal, then try rerunning the search. © 2009 Best Buy Enterprise Services, Inc. All rights reserved. INSIGNIA is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners. ENGLISH 09-0339

  • 1
  • 2

ENGLISH 09-0339
Step 4
Charging the built-in battery
Note
: There is no standby mode for this TV, because it runs on a rechargeable battery.
Turn off your TV before charging the battery. Connect the supplied AC adapter. Charging starts, and the
POWER
ON/CHG
indicator is red. When the charging is completed, the indicator turns off.
Note
: On initial use of the TV, charge the battery for 6 hours.
Step 5
Establish a signal
Make sure that the included rod antenna or a stronger HDTV antenna (not included) is attached to the input at the
top of the TV. Extend the antenna rod and move the TV to a location where it can receive the strongest signal, free
of obstructions and interference from other devices. Press
TV
on your remote control to ensure you are in TV mode.
Step 6
Scan for channels
Note
: See your
User Guide
for more information on connecting your TV
directly to cable or satellite service and for scanning for radio stations.
To scan for channels when the TV signal source is Antenna
Press
MENU
on the remote control, using the
buttons to
highlight
(channel icon). The
Channel
menu opens. Press
OK/ENTER
or
to enter the
Channel
menu. Press the
buttons
to select
Auto Channel Search
, then press
OK/ENTER
or
to enter
the
Auto Channel Search
menu.
Start to Scan
is highlighted. Press
OK/ENTER
or
to start the scan.
If the Automatic Channel Search does not locate the channels you were expecting, try moving the TV to a location
where you can pick up a stronger signal, then try rerunning the search.
Step 3
Connect the AC adapter
Connect the AC adapter into the DC IN jack on the right
side of your unit, then connect the AC adapter to a
100-240V power outlet.
© 2009 Best Buy Enterprise Services, Inc. All rights reserved. INSIGNIA is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.
1
2
Note
: The coin-shaped battery is already in the remote control. The first time you use the remote
control, remove the plastic sheet from the bottom of the battery to activate the remote.
Select
OK:Enter
Menu:Exit
Antenna/Cable
Antenna
80.3
PBS1DTV
Auto Channel Search
Add/Skip Channels
Favorites
Channel No.
Channel Label
Step 2
Install the remote control battery
Remove the battery holder from the back of the remote control by inserting a fingernail into the groove and
pulling out the holder. Place a CR2025 battery with the + side up on the holder. Insert the holder into the
remote control.