Insignia NS-UZ17WH0 Quick Setup Guide - Page 1

QUICK SETUP GUIDE 17 or 21 Cu. Ft. Upright Convertible Freezer/Refrigerator NS-UZ17WH0/ NS-UZ17SS0/NS-UZ17SS0-C/ NS-UZ21WH0/NS-UZ21WH0-C PACKAGE CONTENTS • 17 or 21 Cu. Ft. Upright Convertible Freezer/Refrigerator • Door handle, screws, and hex wrench • Quick Setup Guide FIND YOUR USER GUIDE ONLINE! Go to www.insigniaproducts.com, enter your model in the search box, then press ENTER. Next to Features, click Support & Downloads, then next to User Guide, click the language you want. SETTING UP YOUR FREEZER Before using your freezer • Remove the exterior and interior packing. • Let the freezer stand upright for approximately two hours before connecting it to power. • Wipe the inside. • When moving your freezer, do not tilt it beyond 45° from upright. Finding a suitable location • This freezer is designed to be free standing only, and should not be recessed or built-in. • Place your freezer on a floor that is strong enough to support the freezer when it is fully loaded. • Allow 7.9 inches (20 cm) of space between the sides of the freezer and the walls, 3.9 inches (10 cm) between the back of the freezer and the wall, and 11.8 inches (30 cm) between the top of the freezer and the ceiling. • If you locate the freezer next to a fixed wall, allow sufficient space on the hinge side for the door to swing open. • Locate the freezer away from direct sunlight and sources of heat, such as a stove, heater, or radiator. Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extremely cold temperatures may also prevent the freezer from performing properly. • Avoid locating the freezer in moist areas. Leveling your freezer • If the feet are not adjusted during installation, the doors may not close or seal properly, causing cooling, frost, or moisture problems. • To level your freezer, rotate the leveling feet clockwise (to raise) the freezer or counter-clockwise (to lower). The front of the freezer should be slightly higher than the back. Installing the door handle 1 Unplug the freezer. 2 Screw the extended-head screws into the door holes with a Phillips screwdriver. Do not overtighten. The screw heads should extend above the surface of the door. 3 Loosen the hex screws on the top and bottom of the handle with the hex wrench (provided) so that you can fit the handle over the extended head screws in the door. Hex screws are here. Extra hex screws are provided. USING YOUR FREEZER 1 Plug in your freezer. Wait for 30 minutes, then open the freezer door to determine if the freezer is working properly. 2 Press and hold the Lock button for three seconds, then + or - to set the temperature inside the freezer. A beep sounds when the maximum or minimum temperatures are reached. Using the Lock button • To prevent accidental activation, the control panel automatically locks after 30 seconds of inactivity. To use the control panel, press and hold the Lock button for three seconds. Switching between Freezer and Refrigerator modes This freezer has an advanced design feature that lets you change it from a freezer to a refrigerator. Using the control panel on the freezer 1 Press and hold the Lock button for three seconds. 2 Press and hold the Freezer/Fridge button for three seconds. The panel beeps and the indicator changes to the new mode. Quick Freezing foods • The quick freeze mode lowers the temperature below the normal operating temperature to quickly freeze foods. You can only use the control panel to quick freeze foods. Using the control panel on the freezer 1 Press and hold Lock for three seconds. 2 Press the Quick Freeze button to enter quick freeze mode. The blue snowflake turns on. • The quick freeze mode turns off after three hours if the temperature falls below -13° F (-25° C). If the temperature does not fall below -13° F (-25° C), the quick freeze mode turns off after 24 hours. You can press the button a second time to exit quick freeze mode. Switching between Fahrenheit and Celsius Using the control panel on the freezer 1 Press and hold Lock for three seconds to unlock the control panel. 2 Press and hold + and - for three seconds to switch settings. Before using your new product, please read these instructions to prevent any damage. 4 Place the door handle over the heads of the screws, then tighten the hex screws.