Insignia NS-UZ21XWH7 Quick Setup Guide - Page 1
Insignia NS-UZ21XWH7 Manual
View all Insignia NS-UZ21XWH7 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
QUICK SETUP GUIDE WiFi Connected 17 / 21 Cu.Ft. Upright Freezer NS-UZ17XWH7 / NSUZ21XWH7 PACKAGE CONTENTS • 17 or 21 cubic foot upright freezer with WiFi connection • Door handle, screws, and hex wrench • Quick Setup Guide FIND YOUR USER GUIDE ONLINE! Go to www.insigniaproducts.com, enter your model in the search box, then press ENTER. Next to Features, click Support & Downloads, then next to User Guide, click the language you want. SETTING UP YOUR FREEZER Before using your freezer • Remove the exterior and interior packing. • Let the freezer stand upright for approximately two hours before connecting it to power. • Wipe the inside. • When moving your freezer, do not tilt it beyond 45° from upright. Finding a suitable location • This freezer is designed to be free standing only, and should not be recessed or built-in. • Place your freezer on a floor that is strong enough to support the freezer when it is fully loaded. • If your freezer is located too far from your WiFi router, the signal may be too weak for a good connection. If that's the case, a WiFi range extender should improve connectivity. • Allow 7.9 inches (20 cm) of space between the sides of the freezer and the walls, 3.9 inches (10 cm) between the back of the freezer and the wall, and 11.8 inches (30 cm) between the top of the freezer and the ceiling. • If you locate the freezer next to a fixed wall, allow sufficient space on the hinge side for the door to swing open. • Locate the freezer away from direct sunlight and sources of heat, such as a stove, heater, or radiator. Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extremely cold temperatures may also prevent the freezer from performing properly. • Avoid locating the freezer in moist areas. Leveling your freezer • If the feet are not adjusted during installation, the doors may not close or seal properly, causing cooling, frost, or moisture problems. • To level your freezer, rotate the leveling feet clockwise (to raise) the freezer or counter-clockwise (to lower). The front of the freezer may be slightly higher than the back. Before using your new product, please read these instructions to prevent any damage. Installing the door handle 1 Unplug the freezer. 2 Screw the extended-head screws into the door holes with a Phillips screwdriver. Do not overtighten. The screw heads should extend above the surface of the door. 3 Loosen the hex screws on the top and bottom of the handle with the hex wrench (provided) so that you can fit the handle over the extended head screws in the door. Hex screws are here. Extra hex screws are provided. 4 Place the door handle over the heads of the screws, then tighten the hex screws. USING YOUR FREEZER 1 Plug in your freezer. Wait for 30 minutes, then open the freezer door to determine if the freezer is working properly. 2 Press and hold the Lock button for three seconds, then + or - to set the temperature inside the freezer. A beep sounds when the maximum or minimum temperatures are reached. Using the Lock button • To prevent accidental activation, the control panel automatically locks after 30 seconds of inactivity. To use the control panel, press and hold the Lock button for three seconds. Switching between Freezer and Refrigerator modes This freezer has an advanced design feature that lets you change it from a freezer to a refrigerator. You can only use the control panel to switch modes. You cannot use the Insignia Connect App to switch modes. 1 Press and hold the Lock button for three seconds. 2 Press and hold the Freezer/Fridge button for three seconds. The panel beeps and the indicator changes to the new mode. Quick Freezing foods • The quick freeze mode lowers the temperature below the normal operating temperature to quickly freeze foods. You can only use the control panel to quick freeze foods. You cannot use the Insignia Connect App. 1 Press and hold Lock for three seconds. 2 Press the Quick Freeze button to enter quick freeze mode. The blue snowflake turns on. • The quick freeze mode turns off after three hours if the temperature falls below -13° F (-25° C). If the temperature does not fall below -13° F (-25° C), the quick freeze mode turns off after 24 hours. You can press the button a second time to exit quick freeze mode. Switching between Fahrenheit and Celsius Using the control panel on the freezer 1 Press and hold Lock for three seconds to unlock the control panel. 2 Press and hold + and - for three seconds to switch settings. Using the App • Tap Edit, then tap the slider next to Temperature Unit. INTRODUCING THE INSIGNIA CONNECT APP Download the Insignia Connect app to use additional features such as open-door and temperature alerts. App download is optional - your freezer works normally without it! CONNECTING YOUR FREEZER TO WIFI (OPTIONAL) 1 Make sure that your mobile device is connected to your preferred WiFi network. 2 Download and open the free Insignia Connect Device app from the App Store or Google Play. (Apple: iOS 9 or later, Android: 6.0.1 Marshmallow or later) 3 Log in or sign up for a Best Buy or Insignia Connect Device account. 4 On your freezer, press and hold Lock to unlock the control panel. 5 Press and hold - and Lock at the same time until you hear a beep and see "0" on the control panel. 6 Press + once. "AP" is displayed. 7 In the app, tap Set Up Device, then follow the on-screen directions to complete setup. Note: The control panel will display the temperature after ten seconds, but WiFi pairing mode will remain active. • You may need to repeat steps 4-6 to put the freezer back into AP mode if the app cannot find your freezer. • Your freezer uses the 2.4GHz WiFi spectrum. If your router provides both 2.4GHz and 5GHz, select the 2.4GHz band.