Intel 510T User Guide - Page 120

intermediate gateway- required if the TFTP - switch factory reset

Get Intel 510T - Express Scalable Switch 10/100 Fast Enet 24Pt PDF manuals and user guides
UPC - 735858114219
View all Intel 510T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

C H A P T E R 7 Console Port Use and Troubleshooting Commands allowed in Maintenance Mode bootptab file entry The following command is available for the switch in Maintenance Mode: Command Use TFTP ownIP tftpIP [gwIP] Loads software using the TFTP protocol : the name of the file containing the software ownIP: your own IP address tftpIP: the IP address of the TFTP host [gwIP: the IP address of the primary router (intermediate gateway)- required if the TFTP server is located on a remote part of the network BOOTP Loads software using the BOOTP or TFTP protocol : the name of the file containing the software DUMP addr Dumps memory contents INFO Shows hardware information RESET Resets the switch RUN defparm Starts the software in its default factory settings The entry for the switch in the bootptab should contain a line similar to: :bf=/intel/switch/es510_x.xx: This instructs the switch to load the switch software from the bootp/ tftp server. Use the Intel Device View application to configure the switch manually, or transfer the inxxxxxx.p file containing the configuration from a TFTP server to the switch. 110

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
C H A P T E R 7
Console Port Use and Troubleshooting
110
Commands allowed in
Maintenance Mode
The following command is available for the switch in Maintenance
Mode:
bootptab file entry
The entry for the switch in the
bootptab
should contain a line sim-
ilar to:
:bf=/intel/switch/es510_x.xx:
This instructs the switch to load the switch software from the bootp/
tftp server. Use the Intel Device View application to configure the
switch manually, or transfer the inxxxxxx.p file containing the con-
figuration from a TFTP server to the switch.
Command
Use
TFTP <filename> ownIP tftpIP [gwIP]
Loads software using the TFTP protocol
<filename>
: the name of the file containing
the software
ownIP
: your own IP address
tftpIP
: the IP address of the TFTP host
[gwIP:
the IP address of the primary router
(intermediate gateway)— required if the TFTP
server is located on a remote part of the network
BOOTP <filename>
Loads software using the BOOTP or TFTP pro-
tocol
<filename>
: the name of the file containing
the software
DUMP addr
Dumps memory contents
INFO
Shows hardware information
RESET
Resets the switch
RUN defparm
Starts the software in its default factory settings