Intel AXXSASIOMOD Configuration Guide - Page 16

Product Code ASR2500SAS2 FSR2500LXFAN FSR2500BRPFAN ASRLXFANS ASR2500PS ADRBEZBLACK ADRLCDBEZEL ADRTAPEKIT ASR2500SATAPE ASR2500SIXDRV ASR2500EESPR ASR2500CHSPR UPC 00735858184014 00735858184021 00735858184038 00735858184045 00735858184052 00735858165129 00735858165082 00735858165075 00735858184069 00735858184076 00735858184083 00735858184090 MM 881261 880525 882057 881263 881262 857675 857586 882437 881260 901833 881265 880281 Description SR2500- SAS PCI Cable Kit - Supports cabling from an add-in PCI card with SFF-8484 ganged connector in the full-height slot to the passive Midplane only. This cable is recommended for use with the Intel® RAID controller SRCSAS18E (5 Pack). SR2500 LX hot-swap redundant fan spare kit - Contains 3 fans (1 x 60mm, 2 x 80mm). Notes: Not compatible with BRP SKU fans. This SKU can also be used to add second bank of fans to upgrade the KDK SKU to achieve redundant cooling. SR2500 BRP Non-redundant fan spare kit - Contains two fans, one of each type (1 x 60mm, 1 x 80mm) - Not compatible with SR2500 LX SKU fans. BRP to LX Fan upgrade kit. This is a complete set of redundant/hot-swap fans (six total) along with hot-swap fan bracket and cabling. The upgrade requires removing the BRP fans and fan brackets and replacing the entire assembly. BRP and LX fans are not interchangeable. SR2500 750-W power supply module spare/upgrade. This is required to provide redundant power (1+1). SR2400/SR2500 black bezel for use with standard control panel (no LCP cutout). SR2400/SR2500 (2U) black bezel with cutout for Intel® Local Control Panel (LCD). Note: This requires Intel® Local Control Panel. Qty 5 1 1 1 1 1 1 SR2400/SR2500 SCSI tape mounting kit that contains 1 tape tray, drive power cable (which connects to backplane) and terminated SCSI cable. Notes: This kit requires a third- party SCSI PCI add-in card with SR2500. Note: Either this option or the sixth SAS/SATA drive kit can be installed (both cannot be supported simultaneously). SR2500 SAS/SATA tape drive mounting kit that contains 1 tape drive mounting tray, one SATA/SAS cable and one power cable for tape drive (which connects to backplane). Note: Either this option or the sixth SAS/SATA drive kit can be installed (both cannot be supported simultaneously). SR2500 Sixth SAS / SATA drive kit that contains one 3.5- 1 inch drive carrier, backplane board insert, and cables (one power and one SAS/SATA) to enable a sixth hot-swap SAS or SATA drive. Note: Either this option or a Tape drive kit can be installed (both cannot be supported simultaneously). SR2500 Electrical spares kit that contains one each of the 1 following: Hot-swap backplane board, sixth drive backplane board and cables, SAS midplane, passive midplane, bridge board, front control panel board, optical drive interposer board, PCI-X active riser, PCI-X passive riser, PCI Express* FH riser, PCI Express* low-profile riser, optical drive (IDE) cable, redundant fan cable bracket assembly, USB floppy cable, serial cable, I2C cable, SATA/SAS cables, tape drive power cable, 80-mm BRP fan, 80-mm LX fan, 60-mm BRP fan, 60-mm LX fan, LCP interposer board. SR2500 Mechanical spares kit that contains spare PCI 1 bracket assembly, BRP fan mounting structure, LX fan mounting structure, power supply air baffle, CPU duct assembly, hard drive carrier, hard drive carrier blank (for sixth drive/tape bay), sixth drive filler panel, metal fillers for GCM and I/O module knockouts, optical drive tray, optical drive bay filler panel, USB floppy adapter tray for optical bay, HDD to USB floppy adapter tray, tape drive mounting 16