Intel D845PEBT2 Product Guide - Page 16

LAN Subsystem, LAN Subsystem Software, RJ-45 LAN Connector LEDs, Hi-Speed USB 2.0 Support - motherboard drivers

Get Intel D845PEBT2 PDF manuals and user guides View all Intel D845PEBT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Intel Desktop Board D845PEBT2 Product Guide LAN Subsystem The Intel 82562ET (with the Intel 82801DB ICH4) provides a Fast PCI LAN subsystem providing both 10Base-T and 100Base-TX connectivity. The Intel 82562ET provides the following functions: • Basic 10/100 Ethernet LAN connectivity • Supports RJ-45 connector with status indicator LEDs • Programmable transit threshold • Configurable EEPROM that contains the MAC address LAN Subsystem Software For LAN software and drivers, refer to the D845PEBT2 link on Intel's World Wide Web site at: http://support.intel.com/support/motherboards/desktop RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN connector. Table 3 describes the LED states when the board is powered up and the LAN subsystem is operating. Table 3. RJ-45 LAN Connector LEDs LED Color LED State Indicates Green Off 10 Mbit/sec data rate is selected. On 100 Mbit/sec data rate is selected. Yellow Off LAN link is not established. On (steady state) LAN link is established. On (brighter and pulsing) The computer is communicating with another computer on the LAN. Hi-Speed USB 2.0 Support ✏ NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. This desktop board supports up to six USB 2.0 ports via ICH4; four ports routed to the back panel and two routed to a USB front panel header. The box contents include a two port USB adapter that connects to the front panel header and mounts to an empty chassis slot (see page 35 for instructions on how the install the USB 2.0 adapter). USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling Hi-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Intel Desktop Board D845PEBT2 Product Guide
16
LAN Subsystem
The Intel 82562ET (with the Intel 82801DB ICH4) provides a Fast PCI LAN subsystem providing
both 10Base-T and 100Base-TX connectivity.
The Intel 82562ET provides the following
functions:
•
Basic 10/100 Ethernet LAN connectivity
•
Supports RJ-45 connector with status indicator LEDs
•
Programmable transit threshold
•
Configurable EEPROM that contains the MAC address
LAN Subsystem Software
For LAN software and drivers, refer to the D845PEBT2 link on Intel
’
s World Wide Web site at:
RJ-45 LAN Connector LEDs
Two LEDs are built into the RJ-45 LAN connector.
Table 3 describes the LED states when the
board is powered up and the LAN subsystem is operating.
Table 3.
RJ-45 LAN Connector LEDs
LED Color
LED State
Indicates
Off
10 Mbit/sec data rate is selected.
Green
On
100 Mbit/sec data rate is selected.
Off
LAN link is not established.
On (steady state)
LAN link is established.
Yellow
On (brighter and pulsing)
The computer is communicating with another computer on
the LAN.
Hi-Speed USB 2.0 Support
✏
NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC
Class B requirements, even if no device or a low-speed USB device is attached to the cable.
Use a
shielded cable that meets the requirements for a full-speed USB device.
This desktop board supports up to six USB 2.0 ports via ICH4; four ports routed to the back panel
and two routed to a USB front panel header.
The box contents include a two port USB adapter that
connects to the front panel header and mounts to an empty chassis slot (see page 35 for instructions
on how the install the USB 2.0 adapter).
USB 2.0 ports are backward compatible with USB 1.1
devices.
USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates.
Disabling Hi-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation.
This may
be required to accommodate operating systems that do not support USB 2.0.