Intel D865GBF Product Guide - Page 20

RJ-45 LAN Connector LEDs, Hi-Speed USB 2.0 Support - lan driver

Get Intel D865GBF - Desktop Board Motherboard PDF manuals and user guides View all Intel D865GBF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Intel Desktop Boards D865GBF/D865GLC Product Guide RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN connector. Table 6 describes the LED states when the board is powered up and the 10/100 Ethernet LAN subsystem is operating. Table 6. RJ-45 10/100 Ethernet LAN Connector LEDs LED Color Green Yellow LED State Off On Off On (steady state) On (brighter and pulsing) Indicates 10 Mbit/sec data rate is selected. 100 Mbit/sec data rate is selected. LAN link is not established. LAN link is established. The computer is communicating with another computer on the LAN. Table 7 describes the LED states when the board is powered up and the 10/100/1000 Gigabit Ethernet LAN subsystem is operating. Table 7. RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs LED Color Bi-color LED Green LED State Off Green Yellow Off On (steady state) On (brighter and pulsing) Indicates 10 Mbit/sec data rate is selected. 100 Mbit/sec data rate is selected. 1 Gbit/sec data rate is selected. LAN link is not established. LAN link is established. The computer is communicating with another computer on the LAN. Hi-Speed USB 2.0 Support NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. The desktop board supports up to eight USB 2.0 ports via ICH5; four ports routed to the back panel and four routed to the internal USB 2.0 headers. USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0. NOTE USB devices are limited to USB 1.1 transfer rates prior to operating system and driver initialization. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Intel Desktop Boards D865GBF/D865GLC Product Guide
20
RJ-45 LAN Connector LEDs
Two LEDs are built into the RJ-45 LAN connector.
Table 6 describes the LED states when the
board is powered up and the 10/100 Ethernet LAN subsystem is operating.
Table 6.
RJ-45 10/100 Ethernet LAN Connector LEDs
LED Color
LED State
Indicates
Off
10 Mbit/sec data rate is selected.
Green
On
100 Mbit/sec data rate is selected.
Off
LAN link is not established.
On (steady state)
LAN link is established.
Yellow
On (brighter and pulsing)
The computer is communicating with another computer on the
LAN.
Table 7 describes the LED states when the board is powered up and the 10/100/1000 Gigabit
Ethernet LAN subsystem is operating.
Table 7.
RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs
LED Color
LED State
Indicates
Off
10 Mbit/sec data rate is selected.
Bi-color LED
Green
100 Mbit/sec data rate is selected.
Yellow
1 Gbit/sec data rate is selected.
Off
LAN link is not established.
On (steady state)
LAN link is established.
Green
On (brighter and
pulsing)
The computer is communicating with another computer on the
LAN.
Hi-Speed USB 2.0 Support
NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC
Class B requirements, even if no device or a low-speed USB device is attached to the cable.
Use a shielded cable that meets the requirements for a full-speed USB device.
The desktop board supports up to eight USB 2.0 ports via ICH5; four ports routed to the back
panel and four routed to the internal USB 2.0 headers.
USB 2.0 ports are backward compatible
with USB 1.1 devices.
USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates.
Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation.
This
may be required to accommodate operating systems that do not support USB 2.0.
NOTE
USB devices are limited to USB 1.1 transfer rates prior to operating system and driver
initialization.