Intel DH61DL DH61DL Technical Product Specification - Page 67

Error Messages and Beep Codes - problems

Get Intel DH61DL PDF manuals and user guides View all Intel DH61DL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

4 Error Messages and Beep Codes 4.1 Speaker The board-mounted piezoelectric speaker provides audible error code (beep code) information during POST. For information about The location of the onboard speaker Refer to Figure 1, page 13 4.2 BIOS Beep Codes Whenever a recoverable error occurs during POST, the BIOS causes the board's piezoelectric speaker to beep an error message describing the problem (see Table 36). Table 36. BIOS Beep Codes Type Pattern F2 Setup/F10 Boot Menu Prompt One 0.5 second beep when BIOS is ready to accept keyboard input BIOS update in progress None Video error (no add-in graphics card installed) On-off (1.0 second each) two times, then 2.5-second pause (off), entire pattern repeats (beeps and pause) once and the BIOS will continue to boot. Memory error Thermal trip warning On-off (1.0 second each) three times, then 2.5-second pause (off), entire pattern repeats (beeps and pause) until the system is powered off. Alternate high and low beeps (1.0 second each) for eight beeps, followed by system shut down. Frequency/Comments 932 Hz 932 Hz For processors requiring an add-in graphics card 932 Hz High beep 2000 Hz Low beep 1500 Hz 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
67
4
Error Messages and Beep Codes
4.1
Speaker
The board-mounted piezoelectric speaker provides audible error code (beep code)
information during POST.
For information about
Refer to
The location of the onboard speaker
Figure 1, page 13
4.2
BIOS Beep Codes
Whenever a recoverable error occurs during POST, the BIOS causes the board’s
piezoelectric speaker to beep an error message describing the problem (see Table 36).
Table 36.
BIOS Beep Codes
Type
Pattern
Frequency/Comments
F2 Setup/F10 Boot
Menu Prompt
One 0.5 second beep when BIOS is ready to
accept keyboard input
932 Hz
BIOS update in progress None
Video error (no add-in
graphics card installed)
On-off (1.0 second each) two times, then
2.5-second pause (off), entire pattern repeats
(beeps and pause) once and the BIOS will
continue to boot.
932 Hz
For processors requiring an
add-in graphics card
Memory error
On-off (1.0 second each) three times, then
2.5-second pause (off), entire pattern repeats
(beeps and pause) until the system is powered
off.
932 Hz
Thermal trip warning
Alternate high and low beeps (1.0 second each)
for eight beeps, followed by system shut down.
High beep 2000 Hz
Low beep 1500 Hz