Intel DX38BT Product Guide - Page 39

Installing an MCH Heat Sink Fan (Optional

Get Intel DX38BT - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858194525
View all Intel DX38BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Installing and Replacing Desktop Board Components Installing an MCH Heat Sink Fan (Optional) If your system application requires more MCH cooling than that provided by the MCH passive heat sink, you can add a fan to the heat sink by using the included MCH heat sink fan mounting bracket. This fan mounting bracket is designed to accomodate a 40 mm x 10 mm or 40 mm x 20 mm, 12 V dc fan. You can use the board's 3-pin MCH fan header to supply power to the MCH fan. NOTE An MCH heat sink fan is not included with Desktop Board DX38BT and must be purchased separately. To install an MCH heat sink fan, follow these instructions: 1. Observe the precautions in "Before You Begin" on page 29. 2. Attach the fan (Figure 16, A) to the fan mounting bracket (Figure 16, B) using the fasteners (Figure 16, A) supplied with the fan. Slide the four legs of the bracket over the heat sink fins (Figure 16, C) and push down until the backet "clicks" into place. 3. Attach the fan power connector to the MCH fan header (Figure 16, D). Figure 16. Installation of a Typical MCH Heat Sink Fan 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Installing and Replacing Desktop Board Components
39
Installing an MCH Heat Sink Fan (Optional)
If your system application requires more MCH cooling than that provided by the MCH
passive heat sink, you can add a fan to the heat sink by using the included MCH heat
sink fan mounting bracket.
This fan mounting bracket is designed to accomodate a
40 mm x 10 mm or 40 mm x 20 mm, 12 V dc fan.
You can use the board’s 3-pin MCH
fan header to supply power to the MCH fan.
NOTE
An MCH heat sink fan is not included with Desktop Board DX38BT and must be
purchased separately.
To install an MCH heat sink fan, follow these instructions:
1.
Observe the precautions in "Before You Begin" on page 29.
2.
Attach the fan (Figure 16, A) to the fan mounting bracket (Figure 16, B) using the
fasteners (Figure 16, A) supplied with the fan.
Slide the four legs of the bracket
over the heat sink fins (Figure 16, C) and push down until the backet “clicks” into
place.
3.
Attach the fan power connector to the MCH fan header (Figure 16, D).
Figure 16.
Installation of a Typical MCH Heat Sink Fan