Home » Intel Manuals » Servers » Intel R1000GZ » Manual Viewer

Intel R1000GZ R1000GZ and R1000GL - Page 61

Appendix A: Integration and Usage Tips

Get Intel R1000GZ PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Intel® Server System R1000GZ/GL Product Family TPS Appendix A: Integration and Usage Tips This section provides a list of useful information that is unique to the Intel® Server System R1000GZ/GL Product Family and should be kept in mind while configuring your server system. • Only the Intel® Xeon® processor E5-2600 product family is supported in this Intel server system. Previous generation Intel® Xeon® processors are not supported. • For best system performance, follow memory population guidelines as specified in the Intel® Server Board S2600GZ/GL Technical Product Specification. • For best system performance, follow all thermal configuration guidelines as specified in this document. • DIMM slots E1 thru H3 are only supported when CPU-2 is installed. • The CPU-2 heat sink must be installed at all times, with or without a processor installed. • PCI Riser Slot-2 is only functional when two processors are installed. • The Mini-SAS connector labeled "SCU_01(4-7)" on the server board is only functional when an appropriate Intel® RAID C600 Upgrade Key is installed. • Many embedded SAS and RAID options are available by installing any of several available Intel® RAID C600 Upgrade Keys. • The embedded platform management system may not operate as expected if the platform is not updated with accurate system configuration data. The FRUSDR utility must be run with the system fully configured and each time the system configuration changes for accurate system monitoring and event reporting. • Make sure the latest system software is loaded on the server. This includes System BIOS, BMC Firmware, ME Firmware and FRU & SDR data. The latest system software can be downloaded from http://downloadcenter.intel.com. Revision 2.0 51

Section	Page
1. Introduction	11
1.1 Chapter Outline	11
1.2 Server Board Use Disclaimer	11
1.3 Product Errata	12
2. Product Family Overview	13
2.1 Chassis Dimensions	15
2.2 System Level Environmental Limits	16
2.3 System Features and Options Overview	17
2.3.1 Hot Swap Hard Drive Bay and Front Panel Options	17
2.3.2 Back Panel Features	18
2.3.3 Front Control Panel Options	18
2.4 Server Board Features Overview	19
2.5 Available Front Bezel Support	21
2.6 Available Rack and Cabinet Mounting Kit Options	22
3. Power Subsystem	24
3.1 Mechanical Overview	24
3.2 Power Connectors	26
3.2.1 Power Supply Module Card Edge Connector	26
3.2.2 Riser Card Power Connectors	26
3.2.3 Hot Swap Backplane Power Connector	27
3.2.4 Optical Drive Power Connector	27
3.3 Power Supply Module Efficiency	27
3.4 Power Cord Specification Requirements	28
3.5 Optional Chassis Grounding Support	28
3.6 AC Input Specifications	29
3.6.1 Power Factor	29
3.6.2 AC Input Voltage Specification	29
3.6.3 AC Line Isolation Requirements	29
3.6.4 AC Line Dropout / Holdup	29
3.6.4.1 AC Line 12VSBHoldup	29
3.6.5 AC Line Fuse	30
3.6.6 AC Inrush	30
3.6.7 AC Line Transient Specification	30
3.6.8 Susceptibility Requirements	30
3.6.9 Electrostatic Discharge Susceptibility	31
3.6.10 Fast Transient/Burst	31
3.6.11 Radiated Immunity	31
3.6.12 Surge Immunity	31
3.6.13 Power Recovery	31
3.6.14 Voltage Interruptions	31
3.6.15 Protection Circuits	31
3.6.16 Over-current Protection (OCP)	31
3.6.17 Over-voltage Protection (OVP)	32
3.6.18 Over-temperature Protection (OTP)	32
3.7 Cold Redundancy Support	32
3.7.1 Powering on Cold Standby supplies to maintain best efficiency	32
3.7.2 Powering on Cold Standby supplies during a fault or over current condition	33
3.7.3 BMC Requirements	33
3.7.4 Power Supply Turn On Function	33
3.8 Closed Loop System Throttling (CLST)	33
3.9 Smart Ride Through (SmaRT)	34
3.10 Power Supply Status LED	34
4. Thermal Management	35
4.1 Thermal Operation and Configuration Requirements	35
4.2 Thermal Management Overview	36
4.2.1 Set Throttling Mode	36
4.2.2 Altitude	36
4.2.3 Set Fan Profile	37
4.2.4 Fan PWM Offset	37
4.2.5 Quiet Fan Idle Mode	37
4.2.6 Thermal Sensor Input for Fan Speed Control	37
4.3 System Fans	38
4.4 Power Supply Fans	40
4.5 FRUSDR Utility	40
5. System Storage and Peripheral Options	41
5.1 2.5” Hard Disk Drive Support	41
5.1.1 2.5” Drive Hot-Swap Backplane Overview	42
5.1.2 Cypress* CY8C22545 Enclosure Management Controller	43
5.2 3.5” Hard Disk Drive Support	44
5.2.1 3.5” Drive Hot-Swap Backplane Overview	45
5.2.2 Cypress* CY8C22545 Enclosure Management Controller	46
5.3 Optical Drive Support	46
5.4 eUSB SSD Support	47
5.5 SATA DOM Support	47
6. Storage Controller Options Overview	48
6.1 Embedded SATA / SAS Controller support	48
6.2 Embedded Software RAID Support	49
6.2.1 Intel® Embedded Server RAID Technology 2 (ESRT2) 1	49
6.2.2 Intel® Rapid Storage Technology (RSTe) 1	49
6.3 Intel® Integrated RAID Module Support (Available Option)	50
7. Front Control Panel and I/O Panel Overview	51
7.1 I/O Panel Features	51
7.2 Control Panel Features	52
8. Intel® Local Control Panel	55
9. PCI Riser Card Support	56
9.1 Riser Slot Overview	56
9.2 Riser Card Support	58
10. Mezzanine I/O Module Support	59
10.1 I/O Module Support	59
10.2 Intel® Remote Management Module 4 (RMM4) Lite and Management NIC Support	59
Appendix A: Integration and Usage Tips	61
Appendix B: POST Code Diagnostic LED Decoder	62
Appendix C: POST Code Errors	67
Appendix D: System Configuration Table for Thermal Compatibility	72
Glossary	75