Intel R1000GZ R2000GZ and R2000GL - Page 46

Intel® Xeon Phi™ Coprocessor Card – System Configuration Requirements

Get Intel R1000GZ PDF manuals and user guides View all Intel R1000GZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Intel® Server System R2000GZ/GL Product Family TPS • A system configured with the contents of Intel Accessory Kit AGZCOPRODUCT can support the following add-in card configurations. o Add-in cards with minimum 100 LFM (0.5 m/s) or 200 LFM (1m/s) air flow requirement can be installed in any available add-in card slot in both Riser Card #1 and Riser Card #2. o Add-in cards with a >200 LFM air flow requirement cannot be supported. o When installing a double wide add-in card, remove the plastic knock-out from the air duct from the side on which the add-in card is installed. Only remove both plastic knock outs when installing two double wide cards (1 per riser card) into the system. Figure 25. Intel Accessory Kit AGZCOPRODUCT - Air Duct Note: System integrators should verify GPGPU add-in card air flow requirements from vendor specifications before integrating them into the system. 5.3 Intel® Xeon Phi™ Coprocessor Card - System Configuration Requirements For best system performance and proper fan speed control, ensure the system is configured as follows: • The minimum system software revisions installed must be:  System BIOS 01.06.0002 or later  BMC Firmware 01.17.4207 or later  FRUSDR 1.09 or later Intel highly recommends that the latest available system software be installed. The latest system update package can be downloaded from the following Intel web site: http://downloadcenter.intel.com • The following BIOS Setup Utility Options must be set:  MMIO over 4GB = Enabled  MMIO Size = 256GB 36 Revision 2.0

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Intel
®
Server System R2000GZ/GL Product Family TPS
36
Revision 2.0
•
A system configured with the contents of Intel Accessory Kit
AGZCOPRODUCT
can support the
following add-in card configurations.
o
Add-in cards with minimum 100 LFM (0.5 m/s) or 200 LFM (1m/s) air flow requirement can be
installed in any available add-in card slot in both Riser Card #1 and Riser Card #2.
o
Add-in cards with a >200 LFM air flow requirement cannot be supported.
o
When installing a double wide add-in card, remove the plastic knock-out from the air duct from
the side on which the add-in card is installed. Only remove both plastic knock outs when
installing two double wide cards (1 per riser card) into the system.
Figure 25. Intel Accessory Kit AGZCOPRODUCT - Air Duct
Note:
System integrators should verify GPGPU add-in card air flow requirements from vendor specifications
before integrating them into the system.
5.3
Intel
®
Xeon Phi™ Coprocessor Card – System Configuration Requirements
For best system performance and proper fan speed control, ensure the system is configured as follows:
•
The minimum system software revisions installed must be:
System BIOS 01.06.0002 or later
BMC Firmware 01.17.4207 or later
FRUSDR 1.09 or later
Intel highly recommends that the latest available system software be installed. The latest system update
package can be downloaded from the following Intel web site: http://downloadcenter.intel.com
•
The following <F2> BIOS Setup Utility Options must be set:
MMIO over 4GB = Enabled
MMIO Size = 256GB