Intel S2400SC Service Guide - Page 80

Removing and Installing 8x2.5\, Removing 8x2.5\, Installing 8x2.5\

Get Intel S2400SC PDF manuals and user guides View all Intel S2400SC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Hardware Installations and Upgrades 10. Install the chassis cover. For instructions, see "Installing the Chassis Cover". 11. Plug all peripheral devices and the AC power cable into the server. 12. Power up the server. Removing and Installing 8x2.5" Hot-swap Hard Drive Cage Assembly Removing 8x2.5" Hot-swap Hard Drive Cage Assembly 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover". 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel (Pedesal Only)". 5. Disconnect the power and data cables to the backplane. 6. Use screwdriver to release the hot-swap hard drive cage (see letter A) from the chassis and remove the hot-swap hard drive cage (see letter B). Figure 100. Removing the 8x2.5" HDD Cage Assembly Installing 8x2.5" Hot-swap Hard Drive Cage Assembly CAUTION It is critical that you connect the SAS/SATA data cables correctly from the SAS/SATA backplane to your server board or RAID controller card. Failure to do so may result in data loss. 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover". 64 Intel® Server Board S2400SC Intel® Server System P4000SC Family Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
Hardware Installations and Upgrades
64
Intel
®
Server Board S2400SC Intel
®
Server System P4000SC Family Service Guide
10.
Install the chassis cover. For instructions, see “Installing the Chassis Cover”.
11.
Plug all peripheral devices and the AC power cable into the server.
12.
Power up the server.
Removing and Installing 8x2.5" Hot-swap Hard Drive
Cage Assembly
Removing 8x2.5" Hot-swap Hard Drive Cage Assembly
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.
4.
Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel
(Pedesal Only)”.
5.
Disconnect the power and data cables to the backplane.
6.
Use screwdriver to release the hot-swap hard drive cage (see letter
A
) from the chassis and
remove the hot-swap hard drive cage (see letter
B
).
Figure 100. Removing the 8x2.5" HDD Cage Assembly
Installing 8x2.5" Hot-swap Hard Drive Cage Assembly
CAUTION
It is critical that you connect the SAS/SATA data cables correctly from the SAS/SATA
backplane to your server board or RAID controller card. Failure to do so may result in
data loss.
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.