Intel S875WP1 Product Guide - Page 19

USB, High-Speed USB 2.0 Support, Legacy USB Support - e driver

Get Intel S875WP1 - EATX MBD 875 P4 DDR-2CH SATA RAID VID GETH PDF manuals and user guides
UPC - 735858161381
View all Intel S875WP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

USB High-Speed USB 2.0 Support ✏ NOTES Use a shielded cable that meets the requirements for a full-speed USB device. Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a lowspeed USB device is attached to the cable. USB devices are limited to USB 1.1 transfer rates prior to operating system and driver initialization. The server board supports up to six USB 2.0 ports via the ICH5. Four ports are routed to the back panel. One header, supporting up to two ports, is routed to the front panel. USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling High-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0. Legacy USB Support Legacy USB support allows USB devices such as keyboard, mice, and hubs to be used even when the operating system's USB drivers are not available. Legacy USB support is used to access the BIOS Setup program, and to install an operating system that supports USB. By default, Legacy USB support is set to Enabled. Four of the USB ports are implemented with stacked back panel connectors; the other two are accessible via the front panel USB header. The S875WP1-E server board fully supports UHCI and uses UHCI-compatible software drivers. ✏ NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use s shielded cable that meets the requirements for full-speed devices. Server Board Features 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Server Board Features
19
USB
High-Speed USB 2.0 Support
NOTES
Use a shielded cable that meets the requirements for a full-speed USB
device.
Computer systems that have an unshielded cable attached to a USB
port might not meet FCC Class B requirements, even if no device or a low-
speed USB device is attached to the cable.
USB devices are limited to USB 1.1 transfer rates prior to operating system
and driver initialization.
The server board supports up to six USB 2.0 ports via the ICH5.
Four ports are routed to the back
panel.
One header, supporting up to two ports, is routed to the front panel.
USB 2.0 ports are
backward compatible with USB 1.1 devices.
USB 1.1 devices will function normally at USB 1.1
speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates.
Disabling High-Speed USB in BIOS reverts all USB 2.0 ports to USB 1.1 operation.
This
may be required to accommodate operating systems that do not support USB 2.0.
Legacy USB Support
Legacy USB support allows USB devices such as keyboard, mice, and hubs to be used even when
the operating system’s USB drivers are not available.
Legacy USB support is used to access the
BIOS Setup program, and to install an operating system that supports USB.
By default, Legacy
USB support is set to Enabled.
Four of the USB ports are implemented with stacked back panel connectors; the other two are
accessible via the front panel USB header.
The S875WP1-E server board fully supports UHCI and
uses UHCI-compatible software drivers.
NOTE
Computer systems that have an unshielded cable attached to a USB port may not
meet FCC Class B requirements, even if no device is attached to the cable.
Use
s shielded cable that meets the requirements for full-speed devices.