Intermec CN51 CN51 Mobile Computer Compliance Insert (Model 1015CP01S) - Page 1
Intermec CN51 Manual
View all Intermec CN51 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
CN51 Mobile Computer Compliance Insert Model 1015CP01S For Users in English-Speaking Regions (en) Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future reference. Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user's authority to operate the equipment. Battery, Charger, and Power Supply Information Caution: For use with Intermec battery pack Model 1015AB01 only. See battery instructions. For power supply, use Intermec Model(s) 1015AV01, AE37, or AE36. No user-serviceable parts. Caution: The battery pack used with this product may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from children. 802.11 Radio Precaution Statement Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. A Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual. Radiation Exposure Statement Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1, Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation. If a body worn accessory is not purchased from Intermec, the accessory must contain no metal and provide a 1.00 cm (0.39 in) space between the device and the body. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment. To find RF exposure information, go to www.intermec.com > Products > Computers > Handheld Computers > CN51 > Manuals tab, and then scroll down to Regulatory Information. FCC - Hearing Aid Compatibility (HAC) The 1015CP01S conforms to the FCC rules and ANSI C63.19:2007, and is rated M3-T3 with the rating statement located on its box. The Hearing Aid Compatibility Act of 1988 (HAC Act) requires digital wireless phones to be compatible with hearing-aids to ensure reasonable access to telecommunications services for persons with hearing disabilities. Some hearing devices (hearing aids and cochlear implants) used near some wireless phones may detect interference with buzzing, humming, or whining noise. Some hearing devices are more immune than others to that noise and phones also vary in the amount of interference they generate. Results will vary depending on the user's hearing device and hearing loss. If your hearing device is vulnerable to interference, even a rated phone may not be used successfully. A rating system developed by the Alliance for Telecommunications Industries Solutions (ATIS) for wireless phones is intended to assist hearing device users find phones that may be compatible with their hearing devices. Not all phones have been rated. Phones rated M3 or M4 meet FCC requirements and are likely to generate less interference to hearing devices, where M4 is the better/higher rating. Phones rated T3 or T4 meet FCC requirements and are likely to be more useable with a hearing device's telecoil (T Switch or Telephone Switch), if so equipped, compared to unrated phones, where T4 is the better/higher rating. To check compatibility of your hearing device with this wireless device, the numeric rating values of your hearing device and this wireless device should be added together. A sum of 5 is acceptable for normal use and a sum of 6 or higher is better. For Users in the U.S.A. and Canada Imager and Camera Flash Compliance and Precaution The 1015CP01S is registered with the CDRH as a Class II LASER Product (21 CFR Subchapter J, Part 1040). This product has a maximum output of 1 mW at 630-680 nm. This product complies with IEC 62471:2006-07 for LED safety. This product may use any of the following Intermec scan engines: • EA30 • EA31 To find Laser and Imager classification information for Intermec scan engines, go to www.intermec.com > Products > Computers > Handheld Computers > CN51 > Manuals tab, and then scroll down to Regulatory Information. The camera assembly with flash is classified as: Risk Category 2. Caution: When using the camera flash, keep the camera flash LED at least 317 mm (12.5 in) away from the subject's eyes. Otherwise serious damage to one's eyes may occur. 1