Intermec CN51 CN51 Mobile Computer Compliance Insert (Model 1015CP01U) - Page 1

Intermec CN51 Manual

Page 1 highlights

CN51 Mobile Computer Compliance Insert Model 1015CP01U Complies with IDA Standards DA 102905 For Users in English-Speaking Regions (en) Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future reference. Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user's authority to operate the equipment. Battery, Charger, and Power Supply Information Caution: For use with Intermec battery pack Model 1015AB01 only. See battery instructions. For power supply, use Intermec Model(s) 1015AV01, AE37, or AE36. No user-serviceable parts. Caution: The battery pack used with this product may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from children. 802.11 Radio Precaution Statement Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. A Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual. Radiation Exposure Statement Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1, Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation. If a body worn accessory is not purchased from Intermec, the accessory must contain no metal and provide a 1.00 cm (0.39 in) space between the device and the body. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment. To find RF exposure information, go to www.intermec.com > Products > Computers > Handheld Computers > CN51 > Manuals tab, and then scroll down to Regulatory Information. • Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. • Consult the dealer or an experienced radio television technician for help. For Users in Europe Imager and Camera Flash Compliance and Precaution This product complies with the following standards for laser and LED safety: • IEC 60825-1:2007/EN 60825-1:2008-05: Class 2 (1 mW, 630-680 nm) • IEC 60825-1/EN 60825-1: Class 1 LED Product (imaging options only, no laser label) • IEC 62471:2006-07 for LED safety This product may use any of the following Intermec scan engines: • EA30 • EA31 To find Laser and Imager classification information for Intermec scan engines, go to www.intermec.com > Products > Computers > Handheld Computers > CN51 > Manuals tab, and then scroll down to Regulatory Information. The camera assembly with flash is classified as: Risk Category 2. Caution: When using the camera flash, keep the camera flash LED at least 317 mm (12.5 in) away from the subject's eyes. Otherwise serious damage to one's eyes may occur. If applicable, this product will be provided with a set of laser safety labels illustrated on the last page(s) of this document. If the proper label language is not installed on the device, locate and apply the appropriate label over the existing label. EU - R&TTE Declaration Intermec Technologies Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). To find the EU Declaration of Conformity, go to www.intermec.com > Products > Computers > Handheld Computers > CN51 > Manuals tab and then scroll down to Regulatory Information. 0981 This product is marked with this logo and uses radio frequency bands that are harmonized throughout the European Community. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

1
CN51 Mobile Computer Compliance Insert
Model 1015CP01U
For Users in English-Speaking Regions (en)
Users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories
other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the
compliance of this product and may result in the loss of the user’s authority to operate the equipment.
Battery, Charger, and Power Supply Information
802.11 Radio Precaution Statement
Radiation Exposure Statement
If a body worn accessory is not purchased from Intermec, the accessory must contain no metal and provide a 1.00 cm (0.39 in) space between
the device and the body.
Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits
established for this equipment. To find RF exposure information, go to
www.intermec.com
>
Products
>
Computers
>
Handheld
Computers
>
CN51
>
Manuals
tab, and then scroll down to
Regulatory Information
.
Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
Consult the dealer or an experienced radio television technician for help.
For Users in Europe
Imager and Camera Flash Compliance and Precaution
This product complies with the following standards for laser and LED safety:
IEC 60825-1:2007/EN 60825-1:2008-05: Class 2 (1 mW, 630-680 nm)
IEC 60825-1/EN 60825-1: Class 1 LED Product (imaging options only, no laser label)
IEC 62471:2006-07 for LED safety
This product may use any of the following Intermec scan engines:
EA30
EA31
To find Laser and Imager classification information for Intermec scan engines, go to
www.intermec.com
>
Products
>
Computers
>
Handheld Computers
>
CN51
>
Manuals
tab, and then scroll down to
Regulatory Information
.
The camera assembly with flash is classified as: Risk Category 2.
If applicable, this product will be provided with a set of laser safety labels illustrated on the last page(s) of this document. If the proper label
language is not installed on the device, locate and apply the appropriate label over the existing label.
EU - R&TTE Declaration
Intermec Technologies Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of
R&TTE Directive (1999/5/EC). To find the EU Declaration of Conformity, go to
www.intermec.com
>
Products
>
Computers
>
Handheld
Computers
>
CN51
>
Manuals
tab and then scroll down to
Regulatory Information
.
Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future
reference.
Caution: For use with Intermec battery pack Model 1015AB01 only. See battery instructions. For power supply, use Intermec
Model(s) 1015AV01, AE37, or AE36. No user-serviceable parts.
Caution: The battery pack used with this product may ignite, create a chemical burn hazard, explode, or release toxic materials if
mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from
children.
Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. A
Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual.
Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1,
Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European
Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation.
Caution: When using the camera flash, keep the camera flash LED at least 317 mm (12.5 in) away from the subject’s eyes. Otherwise
serious damage to one’s eyes may occur.
This product is marked with this logo and uses radio frequency bands that are harmonized throughout the
European Community.
Complies with
IDA Standards
DA 102905
0981