Intermec CV61 CV61 Compliance Insert - Page 1

Intermec CV61 Manual

Page 1 highlights

CV61 Compliance Insert Models 1011CM01 Complies with IDA Standards S&E DA 102905 XXXXXXXXXXX For Users in English-Speaking Regions (en) Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future reference. The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user's authority to operate the equipment. Caution: For vehicle installations observe all warnings and cautions contained in the installation instructions. Installations involving vehicle power sources at or above 60 VDC should be performed by a trained service professional to avoid injury or damage to equipment. Caution: For use with Intermec battery pack Model 1011AB01 only. See battery instructions. For power supply, use Intermec Models 9006AE01, 851-070-001, AE10, or 9007AX01. No user-serviceable parts. Caution: For continued protection against risk of fire, replace only with same type and rating of fuse. Battery Information Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from children. Promply dispose of used batteries according to the instructions. Battery Recycling Information Li-ion Li-ion This product contains or uses a lithium-ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. 802.11 Radio Precaution Statement Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards. A Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual. Radiation Exposure Statement Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1, Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment. When installing and using this product, a 20 cm (7.87 in) passing distance must be maintained from the body or head of the user or nearby persons and the antenna. The antenna must not be touched during transmitter operation. For Users in the U.S.A. and Canada U.S.A. Digital Emissions Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

1
CV61 Compliance Insert
Models 1011CM01
For Users in English-Speaking Regions (en)
The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of
accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void
the compliance of this product and may result in the loss of the user’s authority to operate the equipment.
Battery Information
Battery Recycling Information
802.11 Radio Precaution Statement
Radiation Exposure Statement
Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits
established for this equipment.
When installing and using this product, a 20 cm (7.87 in) passing distance must be maintained from the body or head of the user or nearby
persons and the antenna. The antenna must not be touched during transmitter operation.
For Users in the U.S.A. and Canada
U.S.A. Digital Emissions Compliance
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense.
Caution: This marking indicates that the user should read all included documentation before use. Retain this supplement for future
reference.
Caution: For vehicle installations observe all warnings and cautions contained in the installation instructions. Installations
involving vehicle power sources at or above 60 VDC should be performed by a trained service professional to avoid injury or damage
to equipment.
Caution: For use with Intermec battery pack Model 1011AB01 only.
See battery instructions.
For power supply, use Intermec
Models 9006AE01, 851-070-001, AE10, or 9007AX01. No user-serviceable parts.
Caution: For continued protection against risk of fire, replace only with same type and rating of fuse.
Caution: The battery pack used in this device may ignite, create a chemical burn hazard, explode, or release toxic materials if
mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from
children. Promply dispose of used batteries according to the instructions.
Li-ion
Li-ion
This product contains or uses a lithium-ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent
battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid
waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information.
Caution: Users are responsible for configuring the channels of operation that comply with their country regulatory standards.
A
Wireless Network Administrator should review the operating restrictions detailed within the Access Point installation manual.
Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1,
Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European
Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation.
Complies with
IDA Standards
DA 102905
S&E
XXXXXXXXXXX