Home » Intermec Manuals » Electronics Accessories » Intermec IP2L » Manual Viewer

Intermec IP2L Basic Reader Interface Programmer's Reference Manual (BRI versio - Page 108

SELTRIES, SESSION, TAGTYPE, TAGTYPE Identifiers for Each Air Protocol

Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Chapter 4 - BRI Commands SELTRIES SESSION TAGTYPE When SCHEDULEOPT is set to 2, inventory behaves just like SCHEDULEOPT=1 except that any consecutive inventory rounds on the same antenna will toggle between targeting tags in the A state and tags in the B state. This value only applies to EPCC1G2 tags and is useful when dealing with tags that exhibit excessive persistence. For example, some battery powered EPCC1G2 tags have infinite persistence in sessions 1, 2, and 3. Once inventoried from A to B, these tags will stay in the B state and may not be identified if the reader does not run an inventory round targeting B tags. Sets the number of times a group select is attempted. A group select is the command used to start the identify process. Range is 1 to 254. Default is 1. ATTRIBUTE SELTRIES=1 Note: This attribute can be used for EPCglobal Class 1 Gen 2 tags, but is not recommended. Sets the command session parameter to a corresponding EPCglobal Class 1 Gen 2 air protocol command. You can set this attribute to 0, 1, 2, or 3. Default is 2. The following example specifies an EPCglobal Class 1 Gen 2 Select command: ATTRIBUTE SESSION=0 For details about SESSION, see the EPCglobal Inc. specification, EPC™ RadioFrequency Identity Protocols Class-1 Generation-2 UHF RFID Protocol for Communications at 860 MHz-960 MHz Version 1.1.0. Defines the types of RFID tags used in an application. Certain performance improvements can be realized if it is known ahead of time what types of tags are in use. Follow this syntax: ATTRIBUTE TAGTYPE=identifier[,identifier ...] where identifier is one of the values listed in the next table. TAGTYPE Identifiers for Each Air Protocol Identifier MIXED ISO6BG1 or G1 ISO6BG2 or G2 ICODE119 Air Protocol ISO 18000-6B and UCODE119 only ISO 18000-6B ISO 18000-6B UCODE119 Description G1, G2 and v1.19 tags only (MIXED mode is provided for backward compatibility.) ISO6B G1 tags ISO6B G2 tags Phillips v1.19 tags (ISO 18000-6B emulating EPC tag IDs) 96 Basic Reader Interface Programmer Reference Manual

Section	Page
Before You Begin	11
Safety Information	11
Global Services and Support	11
Warranty Information	11
Web Support	11
Send Feedback	11
Telephone Support	12
Who Should Read This Manual	12
Related Documents	12
Chapter 1 - Introducing the Basic Reader Interface	13
Overview of the Basic Reader Interface	14
What’s New?	14
General Features of the BRI Architecture	14
Two Typical BRI Usage Scenarios	14
BRI TCP Applications	15
Choosing a TCP Port for an Application Using TCP	15
Resetting the Reader to the Factory Default Configuration	15
Identifying the Version of BRI on Your Reader	16
Conventions Used in This Manual	17
Chapter 2 - Designing Robust BRI Applications	19
Before You Begin Programming	20
Managing RFID Configuration	20
Using the RFID Resource Kit	21
Recommended Software Structure	21
Programming the BRI Message Layer	23
BRI Message Types	23
BRI Command Processor	24
BRI Asynchronous Event Handler	24
Response Handler	24
Programming the BRI Transport Layer	24
Transport Operation	24
Transport Initialization	25
Multi-Threaded Implementation	25
Chapter 3 - Understanding BRI Programming Elements	27
BRI Logical Interface	28
Using Message Checksums	28
Reserved Keywords	29
Keywords Reserved for BRI Commands	29
Keywords Reserved for Command Parameters	30
Keywords Reserved for Reader Attributes	32
Keywords Reserved for Reader Error and Success Responses	33
Constants	34
Data Field Definitions	34
ANTENNA	34
AFI	35
BIT(memory_bank:startbit, bits)	35
COUNT	35
EPCID	35
HEX(memory_bank:address, length)	36
INT(memory_bank:address, length)	37
ISOUII	38
PC	39
RSSI	39
STRING(memory_bank:address, length)	39
TAGTYPE	40
TIME	40
Data Conditions	40
Using Native Tag Selector Logic in Data Conditions	41
Using AND/OR Logic in Data Conditions	42
Using the AND and OR Keywords	43
Grouping Expressions Without Using Parentheses	44
Using EPCC1G2 Select Logic in Data Conditions	45
Multi-Protocol Condition Usage	46
Chapter 4 - BRI Commands	47
BRI Commands	48
ATTRIBUTE	48
Changing the Reader Attributes	48
Reading the Reader Attributes	50
BLOCKPERMALOCK	50
BLOCKPERMALOCK READ	52
BRIVER	52
CAPABILITIES	53
DIAGNOSTICS	56
ERASE	57
FACDFLT	57
FLEXQUERY	59
HELP	59
HWCC	60
HWID	60
HWPROD	60
HWREGION	60
HWVER	61
KILLTAG	62
LOCK	62
PING	63
PLATDFLT	63
PRESET	64
PRINT	64
PROTECT	64
READ	66
READGPI	72
REPEAT	72
RESET	73
SET	74
SWVER	75
TRIGGER	75
TRIGGERQUEUE	78
TRIGGERREADY	79
TRIGGERWAIT	80
VERSION	80
WRITE	81
WRITEGPO	85
BRI Extensions for NXP Tags	86
NXPALARM	86
NXPCONFIG	87
NXPEAS	87
NXPREADPROTECT	88
BRI Extensions for Fujitsu Tags	88
FJAREAREADLOCK	88
FJAREAWRITELOCK	88
FJAREAWRITELOCKWOPWD	89
FJBURSTERASE	89
FJBURSTWRITE	89
FJCHGAREAGROUPPWD	90
FJCHGBLOCKGROUPPWD	90
FJCHGBLOCKLOCK	91
FJCHGWORDLOCK	91
FJREADBLOCKLOCK	91
BRI Extensions for Impinj Monza 4 Tags	92
READ IMPINJQT	92
WRITE IMPINJQT	92
BRI Extensions for EM Microelectronics Tags	93
READ EMM_GETUID	93
READ EMM_GETSENSOR	93
WRITE EMM_SENDSPI	94
WRITE EMM_RESETALARMS	94
Generic Tag Access Command	94
ACCESSCMD	95
Understanding [READ FIELD] and [WRITE FIELD] Parameters	97
[READ FIELD] Examples	97
[WRITE FIELD] Examples	97
Understanding the <ATTRIBUTE NAME> Parameter	98
ANTENNAS or ANTS	98
ANTTIMEOUT	99
ANTTRIES	99
BAUD	99
BROADCASTSYNC	100
BTPWROFF	100
CHANNEL	100
CHKSUM	100
DENSEREADERMODE	101
ECHO	101
EPCC1G2PARAMETERS	101
FIELDSEP	101
FIELDSTRENGTH	102
IDREPORT	103
IDTIMEOUT	103
IDTRIES	104
INITIALQ	104
INITTRIES	104
LBTCHANNEL	104
LBTSCANENABLE	105
LOCKTRIES	105
NOTAGRPT	105
QUERYSEL	106
QUERYTARGET	106
RDTRIES	106
RPTTIMEOUT	107
SCHEDULEOPT	107
SELTRIES	108
SESSION	108
TAGTYPE	108
TIMEOUTMODE	109
TTY	109
UNSELTRIES	110
UTCTIME	110
XONXOFF	110
WRTRIES	111
Understanding the Timeouts and Tries	111
Setting IDTIMEOUT and ANTTIMEOUT	111
When IDTIMEOUT <= ANTTIMEOUT	111
When IDTIMEOUT > ANTTIMEOUT	112
Setting IDTRIES and ANTTRIES	112
When IDTRIES < ANTTRIES	112
When IDTRIES >= ANTTRIES	113
Setting INITTRIES	114
Understanding the [LITERAL] Parameter	115
Reading and Writing STRING Fields	115
Understanding ACCESS and KILL Passwords	116
Memory Bank 3 User Memory	117
Memory Bank 2 TID Memory	118
Memory Bank 1 EPCID Memory	119
Memory Bank 0 PASSWORD Memory	120
Understanding Error and Success Responses	121
Understanding EVENT Messages	122
Understanding the Format of BRI Command Responses	124
Creating and Using BRI Macros	125
Creating a Command Macro	126
Executing a Command Macro	126
Creating a Parameter Macro	126
Executing a Command With a Parameter Macro	127
Listing All Macros Stored in Memory	127
Displaying the Contents of a Macro	127
Deleting a Macro	127
Chapter 5 - Reader-Specific Platform Specifications	129
Reader-Specific Platform Specifications	130
ITRFxxx01 Readers	130
BRI Disabled by Default	130
Features Not Implemented	130
Buffer Sizes	130
Memory Management	131
Error Responses	131
Antennas	131
GPIO	131
Reader Attributes	131
BRI Commands	132
EVENT Responses	132
Phillips V1.19 TAG Type	132
Readers That Contain the IM5 Module	132
Buffer Sizes	132
Antennas	133
GPIO	133
Reader Attributes	133
FACDFLT Command	133
Readers That Contain the IM4 Module	133
WRITEGPI Command	133
READGPI Command	134
TRIGGER Command	134
Antennas	134
ANTENNA Data Type Definition	134
ANTENNAS or ANTS Attribute	135
Sensing an Over-Temperature Condition	135
Index	137
A	138
B	138
C	139
D	140
E	140
F	140
G	141
H	141
I	141
K	141
L	141
M	141
N	142
O	142
P	142
Q	142
R	142
S	143
T	143
U	143
V	143
W	143

Match case Limit results 1 per page

Chapter 4 — BRI Commands

Basic Reader Interface Programmer Reference Manual

When SCHEDULEOPT is set to 2, inventory behaves just like SCHEDULEOPT=1

except that any consecutive inventory rounds on the same antenna will toggle

between targeting tags in the A state and tags in the B state. This value only applies

to EPCC1G2 tags and is useful when dealing with tags that exhibit excessive

persistence. For example, some battery powered EPCC1G2 tags have infinite

persistence in sessions 1, 2, and 3. Once inventoried from A to B, these tags will stay

in the B state and may not be identified if the reader does not run an inventory

round targeting B tags.

SELTRIES

Sets the number of times a group select is attempted. A group select is the command

used to start the identify process. Range is 1 to 254. Default is 1.

ATTRIBUTE SELTRIES=1

SESSION

Sets the command session parameter to a corresponding EPCglobal Class 1 Gen 2

air protocol command.

You can set this attribute to 0, 1, 2, or 3. Default is 2.

The following example specifies an EPCglobal Class 1 Gen 2 Select command:

ATTRIBUTE SESSION=0<CRLF>

For details about SESSION, see the EPCglobal Inc. specification,

EPC™ Radio-

Frequency Identity Protocols Class-1 Generation-2 UHF RFID Protocol for Communications at

860 MHz–960 MHz Version 1.1.0

TAGTYPE

Defines the types of RFID tags used in an application. Certain performance

improvements can be realized if it is known ahead of time what types of tags are in

use. Follow this syntax:

ATTRIBUTE TAGTYPE=

identifier

...]

where

identifier

is one of the values listed in the next table.

Note:

This attribute can be used for EPCglobal Class 1 Gen 2 tags, but is not

recommended.

TAGTYPE Identifiers for Each Air Protocol

Identifier

Air Protocol

Description

MIXED

ISO 18000-6B and

UCODE119 only

G1, G2 and v1.19 tags only

(MIXED mode is provided for backward

compatibility.)

ISO6BG1

or G1

ISO 18000-6B

ISO6B G1 tags

ISO6BG2

or G2

ISO 18000-6B

ISO6B G2 tags

ICODE119

UCODE119

Phillips v1.19 tags

(ISO 18000-6B emulating EPC tag IDs)