Intermec IP30 IP30NI Compliance Insert - Page 1

IP30NI Compliance Insert Caution: This marking indicates that the user should read all included documentation before use. The Model IP30 Non-Incendive (NI) RFID reader has been qualified by Underwriters Laboratories Inc., to the requirements of the U.S.A. and Canada for use in Class I, Division 2-Groups A,B,C,D; Class II, Division 2-Groups F and G; Class III, Division 2, and non-hazardous locations only. The IP30NI has a T4 temperature code. The IP30NI must only be used with Intermec Model CK3NI, CK61NI, CN3NI, CN4NI, 1000CP01-NI, 1000CP01C-NI, 1000CP01U-NI, 1000CP02-NI, 1000CP02C-NI, 1000CP02U-NI, 1001CP01-NI, 1001CP01C-NI, or 1001CP01U-NI. The users of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the user's authority to operate the equipment. Warning: Explosion Hazard - Substitution of components may impair suitability for Division 2, Class I, II, and III locations. Warning: Explosion Hazard - Batteries must be changed or charged in an area known to be non-hazardous. Use ONLY Intermec battery pack Model AB19. The following additional warnings and cautions must be observed for the safety of the operator and others in potentially hazardous locations: • The IP30NI must only be used when the ambient temperature is between -15 °C and +50 °C (5 °F and +122 °F). • The IP30NI may only be connected to the CK3NI, CK61NI, CN3NI, CN4NI, 1000CP01-NI, 1000CP01C-NI, 1000CP01U-NI, 1000CP02-NI, 1000CP02C-NI, 1000CP02U-NI, 1001CP01-NI, 1001CP01C-NI, or 1001CP01U-NI. Approved computers may only connect to the IP30NI using Bluetooth except for the CK61NI and CN4NI. The CK61NI and CN4NI computers can connect to IP30NI using either a Bluetooth or USB cabled connection. Any cabled connections to the IP30NI must be made prior to entering a potentially hazardous location. • The battery pack must not be removed or installed while in a potentially hazardous location. • Battery pack charging must only take place in locations known to be non-hazardous. • Any connector cover removed while in ordinary locations must be reinstalled prior to entering a Class II or III potentially hazardous location. Note: Contact your Intermec sales representative if the AB19 battery pack is no longer available. Battery, Charger, and Power Supply Information Caution: Use only Intermec battery pack Model AB19. Use of incorrect battery pack may present a risk of fire or explosion. Promptly dispose of used battery pack according to the instruction. Charge only in or with Intermec Models AC6 and AC7. Caution: The battery pack used with this product may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 100 °C (212 °F). Do not short circuit; may cause burns. Keep away from children. Battery Recycling Information Li-ion This product contains or uses a lithium-ion (Li-ion) main battery. When the battery reaches the end of its useful life, the spent battery should be disposed of by a qualified recycler or hazardous materials handler. Do not mix this battery with the solid waste stream. Contact your Intermec Technologies Service Center for recycling or disposal information. Radiation Exposure Statement Radio Wave Exposure and Specific Absorption Rate (SAR) Information Warning: This equipment complies with International Commission on Non-Ionizing Radiation Protection (ICNIRP), IEEE C95.1, Federal Communications Commission Office of Engineering and Technology (OET) Bulletin 65, Canada RSS-102, and European Committee for Electrotechnical Standardization (CENELEC) limits for exposure to radio frequency (RF) radiation. Use of antennas and accessories not authorized may void the compliance of this product and may result in RF exposures beyond the limits established for this equipment. When installing and using the Intermec IP30 RFID reader a 23-cm (9-inch) passing distance must be maintained from the body or head of the user or nearby persons and the IP30 antenna. The antenna must not be touched during transmitter operation. 1