Intermec PB3 PB2 and PB3 Battery Instructions - Page 1

Design and specifications are subject to change without notice. Intermec Li-ion battery (Model 318-040-001) 7.1 x 3.8 x 2.1 cm (2.8 x 1.5 x 0.8 in) 110 g (3.9 oz) Specifications Physical Specifications Capacity and Output Specifications Maximum output: x 7.4 V (16.28 Wh) Nominal output: x 7.4 V (16.28 Wh) 2200 mAh Temperature and Humidity Specifications Operating temperature: -20°C to 60°C (-4°F to 140°F) Charging temperature: 0°C to 45°C (32°F to 113°F) -20°C to 40°C (-4°F to 104°F) 45% to 85% non-condensing 45% to 85% non-condensing Note: In the U.S.A., the EPA does not consider spent Li-ion batteries as hazardous waste. Caution: This battery pack may ignite, create a chemical burn hazard, explode, or release toxic materials if mistreated. Do not incinerate, disassemble, or heat above 80°C (176°F). Do not short circuit; may cause burns. Keep away from children. Use only Intermec charger Models CPS024100240 and EC-556. Use of incorrect charger may present a risk of fire or explosion. CONTAINS LITHIUM-ION BATTERY. WASTE BATTERY MUST PROMPTLY BE RECYCLED OR DISPOSED OF PROPERLY. SEE INSTRUCTIONS. Proper Disposal of Waste Batteries Some of the substances necessary for the proper functioning of batteries are considered harmful to the environment and to human health. It is therefore important that those substances be kept out of the environment. You play an important role in the protection of the environment: 1. Keep all waste batteries out of unsorted trash. 2. Dispose of all waste batteries in separate collection for treatment and recycling. Please contact Intermec for the collection option(s) available in your location. Marking of the battery: 1. The wheeled-bin symbol indicates the requirement for separate collection of the battery. 2. Two letters shown underneath the wheeled bin indicate the presence of a certain substance: a. Hg means Mercury is present b. Cd means Cadmium is present c. Pb means Lead is present 3. The Moebius loop (chasing arrows) indicates that the battery is recyclable. Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2009 Intermec Technologies Corporation. All rights reserved. PB2 and PB3 Battery Instructions *943-217-003* P/N 943-217-003 Product : Dimensions: Storage temperature: Operating humidity: Weight : Capacity : Storage humidity: Important Recommendations y Charge the battery before use. y See "Charging the Battery" for approved charging methods. Use of this battery in other devices could result in damage to the device or battery. y The temperature range for charging batteries is 0°C to 40°C (32°F to 104°F). Do not charge battery packs outside this range. For maximum battery life, charge batteries at 23°C (73°F). y Do not store the battery at temperatures above 60°C (140°F), such as inside a car on a hot day or in direct sunlight, as this may damage the battery. y Battery usage by children should be supervised. y Do not disassemble or open, crush, bend or deform, puncture, shred, or burn. y Do not modify the battery or attempt to insert foreign objects into the battery. y Do not solder directly to the battery contacts. y Do not immerse the battery in water. y Do not short circuit the battery. Keep the battery connector away from metallic items. y Do not apply mechanical shocks or pressure to the battery. y Avoid dropping the battery or the printer. If you suspect that the battery or printer is damaged, send it to an Intermec service center for inspection. y Replace battery only with another Model 318-040-001 battery. These batteries have been tested in accordance with applicable safety standards. Contact your Intermec sales representative or distributor if this battery is no longer available. y Discarded batteries may create a safety hazard. Before disposal, cover the battery connector with electrical insulating tape. PB2 and PB3 Battery Instructions Using This Battery This lithium-ion battery (Model 318-040-001) is designed for use in these printers: y PB2 Mobile Printer y PB3 Mobile Printer Charging the Battery Before using your printer, you need to fully charge the battery. Batteries can be charged after a partial discharge without affecting the original battery capacity. You can charge this battery: y installed in the printer with the printer AC adapter/charger (Model CPS024100240). y in the 2-bay battery charger (Model EC-556). Use only these Intermec-approved charging accessories. For more information, see the printer user's guide.