Intermec PF2i EasyCoder PF2i RFID Kit Installation Instructions
Intermec PF2i Manual
View all Intermec PF2i manuals
Add to My Manuals
Save this manual to your list of manuals |
Intermec PF2i manual content summary:
- Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 1
Installation Instructions RFID Kit for the EasyCoder® PF2i Printer - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 2
service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec. Information and specifications trademark of Camcar Division of Textron Inc. ii RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 3
Services and Support v Who Should Read This Manual v Related Documents vi Patent Information vi Introduction 1 Printer Firmware Requirement 1 Limitations 1 Contents of Installation Kit 2 Important Notes Before Installing 3 Installing the RFID Kit 4 RFID Kit for the EasyCoder PF2i Printer - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 4
iv RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 5
This Manual This document is for the person who is responsible for installing the EasyCoder PF2i RFID Kit. This document provides you with information about how to install the various components of the EasyCoder PF2i RFID Kit. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 6
Title EasyCoder PF2i User's Guide (Fingerprint version) EasyCoder PF- Series Service Manual Fingerprint v8.XX.X Programmer's Reference Manual Part Number 1-960578-XX 1-960579-XX 1-960582-XX The Intermec web site at www.intermec.com contains our documents (as PDF files) that you can download for - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 7
Module (915 MHz RFID frequency band). Printer Firmware Requirement To ensure complete functionality, your printer should be running Intermec Fingerprint v8.72.0 or later. Limitations This device is intended for use in the EasyCoder PF2i printer only. The device is country/region specific and must be - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 8
Guide 3 Media assy including Media Guide, Antenna and Cable 4 Inner Guide 5 Single-Slot I/O Bus Cable 6 RFID Interface Board 7 Screw M3x5 8 Screw M4x6 9 RFID Label 10 Real-Time Clock Quantity 1 1 1 1 1 1 2 1 1 1 RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 9
by an authorized service technician. Intermec assumes no responsibility printer has been switched off and the power cord and communication cables are disconnected. Note: This installation requires a #T10 and a #T20 Torx screwdriver. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 10
the RFID Kit 1 Place the printer on a flat, hard surface. Carefully lay it down on its left side and open the side door. 2 Raise the printhead. 3 Route the antenna connection cable through the opening in the center deck. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 11
4 Carefully lift the upper media guide (a). Remove the edge guides on the shaft (b). a b 5 Slide the inner guide, the media guide (with RFID antenna), the outer guide and the edge guide onto the shaft. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 12
back in place. 7 Put the printer back on its feet. Remove the three screws (a-c) that hold the cover to the electronics compartment. Gently pull out the cover so the console cable can be disconnected from the CPU board. b c a RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 13
on hoJ6w2 to set the real-time clock please refer to the Fingerprint Programmer's Reference Manual (P/N 1-960582XX). 11 ConJ61nect the single-slot I/O cable to connector J62 (marked "EXP BOARD") on the CPU board. EXP BOARD RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 14
the interface board. P35 P1 J61 J62 EXP BOARD 14 Attach the interface board to the printer's rear plate using the two screws that you removed in step 8. 15 Attach the interface antenna cable to the radio module's contact. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 15
the RFID label to the back plate of the printer. 18 Reassemble the printer: Reattach the console cable to the CPU board while putting back the cover over the electronics compartment. Fasten the three screws in the center deck. RFID Kit for the EasyCoder PF2i Printer Installation Instructions - Intermec PF2i | EasyCoder PF2i RFID Kit Installation Instructions - Page 16
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com RFID Kit for the EasyCoder PF2i Printer Installation Instructions *931-039-001* P/N 931-039-001
Installation
Instructions
RFID Kit
for the EasyCoder®
PF2i Printer