Home » Invacare Manuals » Wheelchairs » Invacare 9TPZ » Manual Viewer

Invacare 9TPZ Owners Manual - Page 54

If the wheelchair is equipped with push to lock wheel locks, elevating legrests, and wheel lock

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

11 OPTIONS 11.3 Wheel Lock Extension Handle ƽ WARNING If the wheelchair is equipped with push to lock wheel locks, elevating legrests, and wheel lock extension handles, the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side, otherwise injury or damage may result. Interference between the top of the elevating legrest and the wheel lock extension handle causes the wheel lock to disengage. 1. Remove the existing rubber tip from the wheel lock handle. Discard rubber tip. 2. Secure the wheel lock extension handle to the wheelchair frame by wrapping the elastic cord around the wheelchair frame. 3. Pass the wheel lock extension handle through the loop end of the elastic cord. 4. Slide the wheel lock extension handle on to the wheel lock handle. 5. Repeat STEPS 1-4 for the remaining wheel lock. Wheel Lock Extension Handle Wheel Lock Handle Elastic Cord (Loop End) Wheelchair Frame FIGURE 3 Wheel Lock Extension Handle Invacare®9000 Topaz™Wheelchair 54 Part No 1100869

Section	Page
© 2010 Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by ™ and ®. All trademarks are owned by or li...	2
1 General 6	3
Symbols 6	3
Limited Warranty 7	3
2 Overview 8	3
Label Location 8	3
Component Identification 9	3
Typical Product Parameters 10	3
3 Safety 11	3
General Guidelines 11	3
Safety/Handling of Wheelchairs 17	3
4 Safety Inspection/Troubleshooting. 25	3
Safety Inspection Checklists 25	3
Troubleshooting 27	3
Maintenance 28	3
5 Front Riggings 31	3
Installing/Removing Swingaway Footrest Assembly 31	3
Swingaway Footrest Height Adjustment 32	3
Installing/Removing Elevating Legrest Assembly 32	3
Adjusting Elevating Legrest Assembly 33	3
Raising/Lowering Elevating Legrest Assembly 34	3
Installing Calf Strap 35	3
Heel Loop Replacement 36	3
6 Arms 37	4
Adjusting Armrest Height 37	4
Replacing Desk/Full Length Armrest Pad 39	4
Removing or Replacing Armrest 39	4
7 Seat and Back 41	4
Replacing Seat Upholstery 41	4
Replacing Back Upholstery 42	4
Adjusting Back Height 42	4
Adjusting Seat Depth 43	4
Adjusting Seat Width 43	4
8 Rear Wheels 44	4
Removing/Installing Rear Wheels 44	4
9 Front Casters 45	4
Installing/Replacing Six or Eight-inch Front Casters and Forks 45	4
Front Caster Mounting Adjustments 46	4
10 Anti-tippers/Wheel Locks 47	4
Installing Anti-Tippers 47	4
Using/Adjusting Wheel Locks 49	4
11 Options 52	5
Installing Crutch and Cane Carrier 52	5
Installing Seat Positioning Strap 53	5
Wheel Lock Extension Handle 54	5
Installing/Removing Solid Seat Insert 55	5
Installing/Removing Solid Back Insert 55	5
Installing O2 Holder/Telescoping I.V. Rod with O2 Holder 56	5
Installing Telescoping I.V. Rod 57	5
Installing/Removing Push Bar 61	5
Installing/Removing One-Piece Footboard 62	5
One Piece Footboard Height Adjustment 65	5
1 General	6
1.1 Symbols	6
Warnings	6
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. See the information below for definitions of the signal words.	6
m	6
danger	6
Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.	6
m	6
Warning	6
Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.	6
m	6
caution	6
Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage or minor injury or both.	6
!	6
important	6
Indicates a hazardous situation that could result in damage to property if it is not avoided.	6
i	6
Gives useful tips, recommendations and information for efficient, trouble-free use.	6
1.2 Limited Warranty	7
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.	7
This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer. This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent pur...	7
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.	7
Invacare warrants the side frames and cross members of this product when purchased new and unused to be free from defects in materials and workmanship for a period of three years from the date of purchase from Invacare or a dealer, with a copy of the...	7
For warranty service, please contact the dealer from whom you purchased your Invacare product. In the event you do not receive satisfactory warranty service, please write directly to Invacare at the address at the bottom of this page. Provide dealer...	7
Limitations and Exclusions: The foregoing warranty shall not apply to serial numbered products if the serial number has been removed or defaced, products subjected to negligence, accident, improper operation, maintenance or storage, products modified...	7
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR VIOLATIONS OF AN...	7
Some states do not allow the exclusion or limitation of incidental or consequential damage, or limitation of how long an implied warranty lasts, so the above exclusion and limitation may not be applicable.	7
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND REQUIREMENTS.	7
i	8
1079203 located on seat rail next to the middle H-block.	8
2 Overview	8
2.1 Label Location	8
2.2 Component Identification	9
Seat Upholstery	9
2.3 Typical Product Parameters	10
seat width	10
handrims	10
Overall width	10
wheel locks	10
seat depth	10
caster size	10
overall depth (with riggings)	10
upholstery	10
seat-to-floor	10
frame colors	10
back style	10
weight*	10
back height	10
shipping weight**	10
(Approx.)	10
arm styles	10
Weight limit	10
Front riggings	10
i	10
* Chair only without footrest (30-inches wide X 20-inches deep)	10
**Chair with footrest (30-inches wide X 20-inches deep)	10
rear axle	10
Rear wheels	10
i	15
When changes to the left hand column occur, follow across the chart and refer to the • procedure to maintain the proper stability, safety and handling of the wheelchair.	15
Stability	15
m	15
Warning	15
The back height, front caster position, caster size, seat-to-floor angle, position of the rear wheels, correct anti-tipper as well as the end user's disability or end user's physical condition and capabilities directly relate to the stability of the ...	15
Seat-to-floor heights have specific positions depending on rear wheel size, rear wheel position, front caster position and seat-to-floor angle. These adjustments must be performed by a qualified technician.	15
back height	15
caster position	15
caster size	15
seat-to-floor angle	15
wheel position	15
user condition	15
Anti-tippers	15
Tire Pressure	16
m	16
Warning	16
DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm. The recommended tire pressure is on the sidewall of the...	16
Weight Limitation	16
m	16
Warning	16
Weight limitation is 700 lbs. Weight limitation with heavy duty frame is 1,000 lbs.	16
Weight Training	16
m	16
Warning	16
Invacare does not recommend the use of its wheelchairs as a weight training apparatus. Invacare wheelchairs have not been designed or tested as a seat for any kind of weight training. If occupant uses said wheelchair as a weight training apparatus, I...	16
Wheel Locks	16
m	16
Warning	16
DO NOT attempt to stop a moving wheelchair with wheel locks. Wheel locks are not brakes.	16
If the wheelchair is equipped with push to lock wheel locks, elevating legrests, and wheel lock extension handles, the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side, otherwise injury or damage may res...	16
Engaging the wheel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick. ALWAYS exercise caution when transferring into or out of the wheelchair.	16
Wheelchair Tie Down Restraints	17
m	17
Warning	17
Invacare recommends that wheelchair users not be transported in vehicles of any kind while in wheelchairs. As of this date, the Department of Transportation has not approved any tie-down systems for transportation of a user while in a wheelchair, in ...	17
It is Invacare’s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made available by the auto industry. Invacare cannot and does not recommend any whee...	17
Wheelchair User	17
m	17
Warning	17
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user. However, final selection of the type of wheelchair to be used by an individual rests solely with the user and his/her hea...	17
The intended use for this wheelchair is for the bariatric user.	17
3.1 Safety/Handling of Wheelchairs	17
Safety and handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair. It ...	17
Use this information only as a basic guide. The techniques that are discussed on the following pages have been used successfully by many.	17
Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual. Invacare recognizes and encourages each individual to try what works best for him/her in overcoming architectur...	17
Stability and Balance	18
m	18
Warning	18
Be aware that carrying heavy objects on your lap while occupying the wheelchair may adversely affect the stability of the wheelchair, resulting in serious bodily injury to the user, damage to the wheelchair and surrounding property.	18
This wheelchair has been designed to accommodate one individual. If more than one individual occupies the wheelchair this may adversely affect the stability of the wheelchair, resulting in serious bodily injury to the user and passenger and damage to...	18
To assure stability and proper operation of your wheelchair, you must at all times wear your seat positioning strap and maintain proper balance. Your wheelchair has been designed to remain upright and stable during normal daily activities as long as ...	18
Virtually all activities which involve movement in the wheelchair have an effect on the center of gravity. Invacare recommends using seat/chest positioning straps for additional safety while involved in activities that shift your weight.	18
DO NOT lean forward out of the wheelchair any further than the length of the armrests. Make sure the casters are pointing in the forward position whenever you lean forward. This can be achieved by advancing the wheelchair and then reversing it in a s...	18
Many activities require the wheelchair user to reach, bend and transfer in and out of the wheelchair. These movements will cause a change to normal balance, center of gravity, and weight distribution of the wheelchair.	18
To determine and establish your particular safety limits, practice bending, reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair.	18
Proper positioning is essential for your safety. When reaching, leaning, bending forward, it is important to use the front casters as a tool to maintain stability and balance.	18
Reaching, Leaning and Bending	19
m	19
Warning	19
DO NOT shift your weight or sitting position toward direction you are reaching as the wheelchair may tip over.	19
DO NOT attempt to reach objects if you have pick them up from the floor by reaching down between your knees.	19
DO NOT lean over the top of the back upholstery to reach objects behind you, as this may cause the wheelchair to tip over.	19
Forward	19
Backward	19
FIGURE 1 Reaching, Leaning and Bending	19
Coping With Everyday Obstacles	19
Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair. Keep in mind your center of gravity to maintain stability and balance.	19
Tipping	20
m	20
WARNING	20
DO NOT tip the wheelchair when occupied to traverse curbs or other such obstructions. Always use curb cuts. Otherwise, injury or damage may result.	20
Stairways	20
m	20
WARNING	20
Extreme caution is advised when it is necessary to move an unoccupied wheelchair up or down the stairs. Invacare recommends using two assistants and making thorough preparations. Make sure to use only secure, non-detachable parts for hand-hold supports.	20
DO NOT attempt to lift the wheelchair by any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair.	20
Follow this procedure for moving the wheelchair between floors when an elevator is NOT available:	20
Moving Up Stairs	20
1. Remove the occupant from the wheelchair.	20
2. If necessary, rotate the anti-tippers so the wheels are facing up.	20
3. One assistant (positioned behind the wheelchair), securely grasps a non-removable (non-detachable) part of the wheelchair for leverage and tilts the wheelchair back to the balance point.	20
4. After the wheelchair has been tilted back to the balance point, the assistant behind the wheelchair backs the wheelchair up against the first step.	20
5. The second assistant (positioned in the front of the wheelchair), with a firm hold on a non-detachable part of the framework, lifts the wheelchair up and on to the next stair above and steadies the wheelchair as the assistant behind the wheelchair...	20
6. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway.	20
7. If necessary, rotate the anti-tippers so the wheels are facing down.	20
Moving Down Stairs	21
1. Remove the occupant from the wheelchair.	21
2. If necessary, rotate the anti-tippers so the wheels are facing up.	21
3. One assistant (positioned behind the wheelchair), securely grasps a non-removable (non-detachable) part of the wheelchair for leverage and tilts the wheelchair back to the balance point.	21
4. After the wheelchair has been tilted back to the balance point, the assistant behind the wheelchair rolls the wheelchair up to the edge of the first step.	21
5. The second assistant (positioned in the front of the wheelchair), with a firm hold on a non-detachable part of the framework, lowers the wheelchair down and on to the next stair below and steadies the wheelchair as the assistant in the rear places...	21
6. The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway.	21
7. If necessary, rotate the anti-tippers so the wheels are facing down.	21
FIGURE 2 Stairways	21
Escalators	21
m	21
WARNING	21
DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.	21
Transferring To and From Other Seats	22
m	22
WARNING	22
Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters parallel to the object you are transferring onto. Also be certain the wheel locks are engaged to help prevent th...	22
caution	22
When transferring, position yourself as far back as possible in the seat. This will help prevent damaged upholstery and the possibility of the wheelchair tipping forward.	22
i	22
This activity may be performed independently provided you have adequate mobility and upper body strength.	22
FIGURE 3 Transferring To and From Other Seats	22
Unfolding and Folding Wheelchair	23
m	23
WARNING	23
ALWAYS keep hands and fingers clear of moving parts to avoid injury.	23
DO NOT place hand or fingers on the underside of the seat rail when opening or closing the wheelchair.	23
DO NOT sit or transfer into the wheelchair unless it is fully open and the seat rails are fully seated into the side frame H-blocks.	23
Unfolding	23
1. Tilt the wheelchair toward you (raising the opposite wheel and caster off the ground/floor).	23
2. Place your hand on the top of the seat rail closest to you where the seat upholstery is attached.	23
3. Point your fingers and thumb to the inside of the wheelchair.	23
4. Press downward on the top of the seat rail until the wheelchair is fully open and the seat rails are fully seated in the H-blocks.	23
5. Engage both wheel locks, open the footrest/legrest for clearance and transfer into the wheelchair. Refer to Transferring To and From Other Seats on page 22.	23
Seat Rail	23
Folding Wheelchair	24
1. Swing footrest/legrest in locked position to the front of the wheelchair.	24
2. Pivot footplates upward to vertical position.	24
3. With both hands, grasp the middle of the seat upholstery at the front and back edge and lift up.	24
m	24
caution	24
DO NOT allow upholstery to hang between the cross braces.	24
4. Place excess seat upholstery over the armrest.	24
FIGURE 5 Folding Wheelchair	24
4 Safety Inspection/Troubleshooting.	25
i	25
Every six months or as necessary, take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair. To operate properly and sa...	25
4.1 Safety Inspection Checklists	25
Initial adjustments should be made to suit your personal body structure and preference. Thereafter follow these maintenance procedures:	25
Inspect/Adjust Initially	25
Ensure that the wheelchair rolls straight (no excessive drag or pull to one side).	25
Inspect for loose or missing hardware on frame and crossbraces.	25
Inspect for bent frame or crossbraces.	25
Check that the wheel locks do not interfere with tires when rolling.	25
Check that the wheel lock pivot points are free of wear and looseness.	25
Check that the wheel locks are easy to engage.	25
Ensure that the wheel locks prevent the wheelchair from moving when engaged.	25
Inspect seat and back for rips and sagging.	25
Inspect seat for damaged or missing warning label.	25
Inspect seat and back for loose or broken hardware.	25
Inspect back cane hand grips for wear/looseness/deterioration.	25
Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged. Replace if necessary.	25
Inspect tires for flat spots and wear.	25
m	26
caution	26
As with any vehicle, check the wheels and tires periodically for cracks and wear. Replace if damaged.	26
Check that there is no excessive side movement or binding in the rear wheels when lifted and spun.	26
Inspect rear wheels for cracked, broken or loose spokes.	26
Ensure all spokes are uniformly tight.	26
Inspect handrims for signs of rough edges or peeling.	26
Inspect axle assembly for proper tension by spinning caster. Caster should come to a gradual stop.	26
Adjust front casters/forks bearing system if wheel wobbles noticeably or binds to a stop.	26
Ensure wheel bearings are clean and free of moisture.	26
Inspect casters for cracks and wear.	26
Clean upholstery and armrests.	26
Check that all labels are present and legible. Replace if necessary.	26
Inspect/Adjust Weekly	26
Inspect tires for flat spots and wear.	26
Inspect rear wheels for cracked, broken or loose spokes.	26
Ensure all spokes are uniformly tight.	26
Inspect axle assembly for proper tension by spinning caster. Caster should come to a gradual stop.	26
Inspect/Adjust Monthly	26
Check that the wheel locks do not interfere with tires when rolling.	26
Check that the wheel lock pivot points are free of wear and looseness.	26
Inspect seat and back for loose or broken hardware.	26
Inspect cane hand grips for wear/looseness/deterioration.	26
Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged. Replace if necessary.	27
Adjust front casters/forks bearing system if wheel wobbles noticeably or binds to a stop.	27
Ensure wheel bearings are clean and free of moisture.	27
Inspect/Adjust Periodically	27
Ensure that the wheelchair rolls straight (no excessive drag or pull to one side).	27
Inspect frame and crossbraces for loose or missing hardware.	27
Inspect for bent frame or crossbraces.	27
Check that wheel locks are easy to engage.	27
Ensure that casters are free of debris.	27
Inspect seat and backs for rips and sagging.	27
Inspect seat for damaged or missing warning label.	27
Check that there is no excessive side movement or binding in the rear wheels when lifted and spun.	27
Clean upholstery and armrests.	27
Check that all labels are present and legible. Replace if necessary.	27
4.2 Troubleshooting	27
4.3 Maintenance	28
Maintenance Safety Precautions	28
m	28
warning	28
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may result.	28
Replace any labels that are missing, worn, or torn. Refer to Label Location on page 6 for a listing of the labels and their locations.	28
Caution	28
DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.	28
1. Before using your wheelchair make sure all nuts and bolts are tight.	28
2. Check all parts for damage or wear and replace.	28
3. Check all parts for proper adjustment.	28
m	28
caution	28
As with any vehicle, check the wheels and tires periodically for cracks and wear. Replace if damaged. Replace as recommended, refer to Replacing/Repairing Rear Wheel Tire/Tube on page 29 and Replacing/Repairing Caster Tire/Tube on page 30.	28
4. The rear wheels, casters and tires should be checked periodically for cracks and wear, and should be replaced by a qualified technician if damaged.	28
5. Periodically adjust wheel locks in correlation to tire wear. Refer to Using/Adjusting Wheel Locks on page 49.	28
i	29
Tire wear is excessive if:	29
Pneumatic Tires - there is missing tread or the tires are bald.	29
Urethane Tires - there are cuts, surface defects or the tires are loose on the rims.	29
Rubber Tires - 30% or more of the tire has worn away.	29
Invacare recommends that tires and casters be replaced every five years.	29
6. Periodically check handrims to ensure they are securely attached to the rear wheels.	29
7. Periodically check caster wheel bearings to make sure they are clean and free from moisture. Use a Teflon® lubricant if necessary.	29
8. Check upholstery for sagging, rips or tears.	29
9. Clean upholstery with mild soap and water.	29
10. Replace any labels that are missing, worn, or torn. Refer to Label Location on page 8 for a listing of labels and their locations.	29
m	29
warning	29
When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly. F...	29
11. Hand grips should be checked monthly for wear/looseness/deterioration. Clean if desired. Replace if looseness or deterioration is found.	29
Replacing/Repairing Rear Wheel Tire/Tube	29
m	29
Warning	29
Replacement of solid urethane tires is not recommended. If the solid urethane tire needs repaired, Invacare recommends replacing the complete wheel assembly.	29
Replacement of rear wheel tube must be performed by a qualified technician.	29
Replacing/Repairing Caster Tire/Tube	30
m	30
warning	30
Replacement of solid urethane or semi-pneumatic tires is not recommended. If the solid urethane or semi-pneumatic tires need replaced, Invacare recommends replacing complete caster assembly.	30
For pneumatic tires, replacement of the tire or tube must be performed by a qualified technician.	30
5 Front Riggings	31
m	31
Warning	31
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.	31
5.1 Installing/Removing Swingaway Footrest Assembly	31
Installing	31
1. Turn the swingaway footrest assembly to the side (open footplate is perpendicular to wheelchair).	31
2. Install the hinge plates on the swingaway footrest assembly onto the hinge pins on the wheelchair frame.	31
3. Push the swingaway footrest assembly toward the inside of the wheelchair until it locks into place.	31
4. Repeat STEPS 1-3 for the other footrest assembly.	31
i	31
The footplate will be on the inside of the wheelchair when locked in place.	31
Removing	31
1. Push the footrest release lever inward.	31
2. Rotate swingaway footrest assembly outward.	31
3. Lift the swingaway footrest assembly off the hinge pins.	31
4. Repeat STEPS 1-3 for the other side.	31
Footrest Release Lever	31
FIGURE 1 Installing/Removing Swingaway Footrest Assembly	31
5.2 Swingaway Footrest Height Adjustment	32
1. Remove the swingaway footrest assembly. Refer to Installing/Removing Swingaway Footrest Assembly on page 31.	32
i	32
Lay the assembly on a flat surface to simplify this procedure.	32
2. Remove the two bolts and locknuts that secure the lower footrest assembly to the upper footrest support.	32
3. Reposition the lower footrest assembly to the desired height.	32
4. Install and securely tighten the two bolts and locknuts.	32
5. Repeat STEPS 1-4 for the other footrest.	32
6. Reinstall the swingaway footrest assembly. Refer to Installing/Removing Swingaway Footrest Assembly on page 31.	32
Lower Footrest Assembly	32
FIGURE 2 Swingaway Footrest Height Adjustment	32
5.3 Installing/Removing Elevating Legrest Assembly	32
Installing	32
i	32
For this procedure, refer to FIGURE 3 on page 33.	32
1. Place elevating legrest assembly on the outside of the wheelchair and install the hinge plates onto the hinge pins on the wheelchair frame.	32
2. Rotate elevating legrest assembly toward the inside of the wheelchair until it locks in place.	32
3. Repeat STEPS 1 and 2 for the other legrest assembly.	32
i	32
The footplates will be facing each other when locked in place.	32
4. While sitting in the wheelchair, adjust the legrest to the correct height. Refer to Adjusting Elevating Legrest Assembly on page 33.	33
Removing	33
1. Ensure the elevating legrest is in the lowered position. Refer to Adjusting Elevating Legrest Assembly on page 33.	33
2. To release the elevating legrest assembly push the legrest release handle toward the inside of the wheelchair (facing the front of the wheelchair) and swing the legrest assembly to the outside of the wheelchair.	33
3. Lift the elevating legrest assembly off the hinge pins.	33
Elevating Legrest Assembly	33
FIGURE 3 Installing/Removing Elevating Legrest Assembly	33
5.4 Adjusting Elevating Legrest Assembly	33
i	33
For this procedure, refer to FIGURE 4 on page 34.	33
Adjusting Footrest Height	33
1. While sitting in the wheelchair, remove the two bolts and locknuts securing the lower footrest assembly to the elevating legrest assembly and move the lower footrest assembly up or down until the desired height is achieved.	33
2. Secure the lower footrest assembly to the elevating legrest assembly with the two bolts and locknuts. Securely tighten.	33
3. Repeat STEPS 1-2 on remaining legrest assembly.	33
Adjusting Calfpad	33
1. Remove the two mounting screws securing the calfpad to the calfpad support of the elevating legrest assembly.	33
2. Slide the Calfpad up or down until the desired position is obtained.	33
3. Secure the calfpad to the elevating legrest assembly with the two mounting screws. Securely tighten.	34
4. Repeat steps 1-3 to adjust remaining calfpad.	34
Calfpad Support	34
5.5 Raising/Lowering Elevating Legrest Assembly	34
i	34
For this procedure, refer to FIGURE 5 on page 35.	34
Raising Elevating Legrest Assembly	34
1. An assistant should hold the lower legrest assembly and raise the elevating legrests until one of three desired height positions is obtained.	34
Lowering Elevating Legrest Assembly	34
1. Use one hand to fully support the weight of the user leg and elevating legrest.	34
2. Pull release lever upward with the other hand.	34
3. Gently, lower user leg and elevating legrest down to desired position.	35
4. Repeat steps 1-3 for remaining elevating legrest.	35
Elevating Legrest	35
5.6 Installing Calf Strap	35
1. Remove calf strap from packaged container if it is not already secured to the footrest.	35
2. Secure one side of the calf strap around each footrest.	35
Footrest	35
FIGURE 6 Installing Calf Strap	35
5.7 Heel Loop Replacement	36
1. Remove the two bolts and locknuts that secure the lower footrest assembly to the upper footrest support.	36
2. Remove the lower footrest assembly.	36
3. Remove the mounting screw, spacer and locknut that secure the existing heel loop to the footrest.	36
4. Slide existing heel loop over the slide tube of the lower footrest assembly.	36
5. Install new heel loop.	36
6. Reverse STEPS 1-4 to reassemble.	36
i	36
When securing the heel loop to the footrest assembly, tighten the mounting screw and locknut until the spacer is secure.	36
Locknuts	36
6 Arms	37
m	37
Warning	37
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.	37
6.1 Adjusting Armrest Height	37
m	37
Warning	37
Make sure the height adjustment lever is in the locked position before using the wheelchair.	37
i	37
For this procedure, refer to FIGURE 1 on page 38.	37
1. Unlock the armrest by performing the following:	37
a. Flip the height adjustment lever on the front of the armrest to the up (horizontal) position.	37
b. Pull the height adjustment lock knob on the rear of the armrest and twist 1/4 turn into the unlocked position.	37
2. Adjust armrest to one of five positions.	37
i	37
The height adjustment lever and lock knob MUST be in the unlocked position when placing armrest into the arm assembly.	37
3. Lock the armrest by performing the following:	37
a. Flip the height adjustment lever on the front of the armrest to the down (vertical) position.	37
b. Pull the height adjustment lock knob on the rear of the armrest and twist 1/4 turn into the locked position.	37
4. Repeat STEPS 1-3 for other armrest.	37
Armrest	38
6.2 Replacing Desk/Full Length Armrest Pad	39
1. Remove the mounting screws that secure the armrest pad to the armrest assembly.	39
2. Replace armrest pad and securely tighten with the existing mounting screws.	39
Armrest Pad	39
6.3 Removing or Replacing Armrest	39
m	39
Warning	39
Make sure the armrest release lever is in the locked position before using the wheelchair.	39
i	39
For this procedure, refer to FIGURE 3 on page 40.	39
Removing Armrests	40
1. Unlock the armrest by flipping the armrest release lever to the up (horizontal) position.	40
2. Lift armrest completely out of arm sockets from the wheelchair.	40
Replacing Armrests	40
i	40
Armrest release levers MUST be in the unlocked position when placing armrests into the arm sockets.	40
1. Place armrest into arm sockets located on the side of the wheelchair.	40
2. Lock the armrest by flipping the armrest release lever to the down (vertical) position.	40
Armrest	40
7 Seat and Back	41
m	41
Warning	41
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur.	41
7.1 Replacing Seat Upholstery	41
1. Remove the mounting screws that secure the existing seat upholstery to the wheelchair frame.	41
2. Remove the existing seat upholstery from the wheelchair frame.	41
3. Install new seat upholstery by reversing STEPS 1-2.	41
i	41
The seat upholstery MUST be installed with the warning label facing up.	41
The following chart determines the number of mounting screws for each seat depth	41
Mounting Screws	41
FIGURE 1 Replacing Seat Upholstery	41
7.2 Replacing Back Upholstery	42
1. Remove the eighteen mounting screws and washers that secure the existing back upholstery to the back canes.	42
2. Install and securely tighten the new back upholstery to the back canes with the eighteen mounting screws and washers starting with the top hole of the back cane.	42
Back Cane	42
FIGURE 2 Replacing Back Upholstery	42
7.3 Adjusting Back Height	42
i	42
For this procedure, refer to FIGURE 3 on page 43.	42
1. Remove the four mounting screws and locknuts that secure the two back canes to the wheelchair frame.	42
2. Remove the bottom two back upholstery mounting screws from the cane.	42
3. Reposition the back canes to one of three height adjustment positions:	42
Hole Number	42
1 & 2	42
2 & 3	42
3 & 4	42
back Height	42
i	42
Holes numbered from bottom to top for reference only. (There are no numbers on the back canes).	42
The mounting screws must be securely tightened into the threaded mounting holes of the wheelchair frame before installing the locknuts.	42
4. Reinstall the four (4) mounting screws through the threaded mounting holes of the wheelchair frame and the back cane. Securely tighten.	43
5. Reinstall the four locknuts. Securely tighten	43
6. Reinstall the two back upholstery mounting screws. Securely tighten.	43
Height Adjustment Positions	43
7.4 Adjusting Seat Depth	43