JBL AVR 580 Owners Manual English - Page 13
Channel/8-Channel Direct Input
View all JBL AVR 580 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
IMPORTANT NOTE: The AVR580's so that it controls the device selected. l Night Mode: Press this button to remote may be programmed to control up After pressing one of these buttons, you activate the Night mode. This mode is to eight devices, including the AVR580. must press the AVR Selector Button available in specially encoded digital Before using the remote, it is important to f again to operate the AVR580's func- sources, and it preserves dialogue (center remember to press the Input Selector tions with the remote. channel) intelligibility at low volume Button e that corresponds to the unit you wish to operate. In addition, the AVR580's remote is shipped from the factory to operate the AVR580 and JBL DVD players. The remote is also capable of operating a wide variety of other products using the control codes that are part of the remote. Before using the remote with other products, follow the instructions on pages 40-41 to program the proper codes for the products in your system. f AVR Selector: Pressing this button will switch the remote so that it will operate the AVR580's functions. If the AVR580 is in the Standby mode, it will also turn the AVR580 on. g AM/FM Tuner Select: Press this button to select the AVR580's tuner as the listening choice. Pressing this button when the tuner is already in use will select between the AM and FM bands. levels. m Channel Select Button: This button is used to start the process of setting the AVR580's output levels to an external source. Once this button is pressed, use the ⁄/¤ Buttons n to select the channel being adjusted, then press the Set Button p, followed by the ⁄/¤ Buttons n again, to change the level setting. (See page 36 for more information.) It is also important to remember that many of the buttons on the remote take on different functions, depending on the product selected using the Device Control Selectors. The descriptions shown here primarily detail the functions of the remote when it is used to operate the AVR580. (See page 42 for information about alternate functions for the remote's buttons.) a Power Off Button: Press this button h 6-Channel/8-Channel Direct Input: Press this button to select the device connected to the 8-Channel Direct Inputs 38 . (See page 30 for more information.) i Test Button: Press this button to begin the sequence used to calibrate the AVR580's output levels. (See page 27 for more information on calibrating the AVR580.) j Sleep Button: Press this button to n ⁄/¤ Buttons: These multipurpose buttons are used to change or scroll through items in the on-screen menus, make configuration settings such as digital inputs or delay timing, or to select surround modes. When changing a setting, first press the button for the function or setting to be changed (e.g., press the Surround Mode Selector k to select a sound field mode or the Digital Select Button q to change a digital input) and then press one of these buttons to scroll to place the AVR580 or a selected device place the unit in the Sleep mode. After through the list of options or to increase in the Standby mode. Note that this will the time shown in the display, the or decrease a setting. The sections in turn off the main room functions, but if the AVR580 will automatically go into the this manual describing the individual Multiroom system is activated, it will con- Standby mode. Each press of the button features and functions contain specific tinue to function. changes the time until turn-off in the information on using these buttons for b IR Transmitter Window: Point this window towards the AVR580 when press- following order: 90 80 70 60 50 min min min min min each application. o ‹ Button: This button is used to ing buttons on the remote to make certain that infrared commands are properly 40 min 30 min 20 min 10 min OFF change the menu selection or setting during some of the setup procedures for received. This button is also used to change chan- the AVR580. c Program/SPL Indicator: This three- nels on your TV when the TV is selected. p Set Button: This button is used to color indicator is used to guide you When the AVR580 remote is being pro- enter settings into the AVR580's memory. through the process of programming the grammed with the codes to operate It is also used in the setup procedures for remote or learning commands from a another device, this button is also used in delay time, speaker configuration and remote into the AVR580's remote code the "Auto Search" process. (See page 41 channel output level adjustment. memory and it is also used as a level indicator when using the remote's EzSet capabilities. (See page 27 for more information on setting output levels, and see for more information on programming the remote.) k Surround Mode Selector: Press q Digital Select: Press this button to assign one of the digital inputs 31 34 &* to a source. (See page 31 for more page 41 for information on programming this button to cycle through the DSP, information on using digital inputs.) the remote.) d Power On Button: Press this to turn on the power to a device selected by pressing one of the Input Selectors e. e Input Selectors: Pressing one of these buttons will perform three actions at the same time. First, if the AVR580 is not turned on, this will power up the unit. Next, it will select the source shown on the button as the input to the AVR580. VMAx and Stereo surround modes such as Hall, Theater, VMAx Near and Far, and Surround Off. This button is also used to tune channels when the TV is selected using the device Input Selector e. When the AVR580 remote is being programmed with the codes of another device, this button is also used in the "Auto Search" process. (See page 41 for more information on programming the remote.) r Numeric Keys: These buttons serve as a 10-button numeric keypad to enter tuner preset positions. They are also used to select channel numbers when TV, Cable or SAT has been selected on the remote, or to select track numbers on a CD, DVD or LD player, depending on how the remote has been programmed. s Tuner Mode: Press this button when the tuner is in use to select between Finally, it will change the remote control automatic tuning and manual tuning. 13