JBL PRX815XLF Owners Manual English - Page 15
Features
View all JBL PRX815XLF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Features 1. SYSTEM EQ LED - This light indicates BOOST (PRX825& PRX835 only) or MONITOR (PRX812 & PRX815 only). 2. SYSTEM EQ Button a. Normal and Boost (PRX825 and PRX835 only) - Default (light off) is NORMAL, frequency response is linear and unaltered. When light indicator is on, BOOST is selected and internal equalization is applied to enhance low frequency and high frequency response. b. Main and Monitor (PRX812 & PRX815 only) - Speaker is optimized for MAIN position when light is off, and MONITOR when the light indicator is on. NOTE: This button is also used to Factory Reset speaker settings. See "FACTORY RESETS" on page 19 for more information. 3. FRONT LED Button - This push button allows you to turn on/off the Power LED on the front of the speaker. 4. LIMIT Indicator - There is one YELLOW LED indicator that will illuminate when input clipping occurs or peak output has been reached and the DSP limiter is acting. b. On - The speaker is connected to WI-FI. c. Blinking Slowly - The speaker is in Access Point mode and has not yet established a WIFI connection. d. Blinking Rapidly - The speaker is in Access Point mode and is communicating with a connected device. 13. WI-FI CONNECT Button - This button is used to connect to a WI-FI network for speaker configuration and control using the PRX Connect application. This button has two functions: a. Press and release - Instructs the speaker to try connecting to the configured WI-FI network. b. Press and hold for 2 seconds - Switches between "Access Point" and "Normal" network operating modes. By default, the speaker is in "Normal" network operating mode. Switching to Access Point mode allows all PRX800 speakers in a system to be initially configured for your network router. When switched to Access Point mode, the WI-FI LINK LED will flash slowly. For more information on using WI-FI, see "WI-FI SETUP" on page 18. 5. GAIN Knobs - These gain knobs are for setting the input level of CH1 and CH2. 14. 50/50 MIX LED - This light indicates a 50/50 mix going to the MIX OUT connector. 6. SIGNAL Indicator - There are two LED indicators (one for each channel) that will illuminate GREEN when signal is present at the input connector. 7. MIC LED - This light indicates MIC input level is selected for the channel. 8. MIC SELECT Button - Speaker is in LINE level mode by default. Press and hold the button for 2 seconds to change to MIC level. Light indicator will turn on while in MIC level input. 9. XLR Inputs - Female balanced XLR and 1/4 inch phone jack combo input connectors. 10. RCA SIGNAL LED - This light indicates RCA input signal. 11. RCA Inputs - Female unbalanced RCA input connectors. 12. WI-FI LINK LED - This LED has four states: a. Off - The speaker is not connected to WI-FI. 15. 50/50 MIX Button - This button determines how the inputs are sent to the MIX OUT connector. When disengaged (50/50 LED off, this is the default), a true mix based on how the gains are set between CH1 and CH2 will be sent to the MIX OUT connector. When engaged (50/50 LED on), a 50/50 mix of CH1 and CH2 will be sent to the MIX OUT connector. This button must be pressed and held for 2 seconds to switch between options. 16. MIX OUT Connector - Male balanced XLR output connector. This connector provides a full-range signal which can be daisy chained to another speaker. 17. REMOTE EQ LED - Indicates the speaker has settings applied by the WI-FI application. 18. POWER LED - This LED illuminates when the "Power Switch" has been turned to the on position. It will illuminate BLUE when the system has power and is ready to pass audio. 15